D10INFP BANNER ENGINEERING, D10INFP Datasheet - Page 2

• Manufacturer Part Number: D10INFP
• Description: Photoelectric Sensor
• Manufacturer: BANNER ENGINEERING
• Type: Analog And Discrete Outputr

Specifications of D10INFP

• Sensor Output: NPN
• Contact Current Max: 150mA
• Switch Terminals: Connector
• Peak Reflow Compatible (260 C): No
• Sensor Input: Fiber Optic
• Output Type: Transistor
• Leaded Process Compatible: No
• Fiber Optic Sensor Type: Analog And Discrete Output

The D10 Expert Sensor is a high-performance plastic fiber-optic sensor whose many
configuration (TEACH-mode) options make it suitable for demanding applications.
Even with all its features, it is extremely easy to use. Advanced 16-bit microcontroller
technology makes this possible.
The D10 Expert provides high-performance sensing in low-contrast applications. Expert
TEACH and setup options provide static, dynamic and single-point programming plus
manual fine adjustment, remote programming and push button lockout. Its slender,
stylized housing has a large digital display visible beneath a clear cover for easy
programming and status monitoring during operation. The sensor mounts directly to
standard 35 mm DIN rail or using the supplied mounting bracket.
The sensor features two outputs with independent setpoints: one of two analog
choices, depending on model, and one discrete (NPN or PNP, also depending on
model). Built-in crosstalk avoidance protocol provides trouble-free operation for
multiple sensors in one area.
D10 Expert
2
** ø0.010" bifurcated fiber not recommended in these speed settings. Contact Banner Applications for more information.
Light/Dark Operate
Selection
OFF-Delay Timing
Selection
Display Selection
Power Level/Speed
Selection
Response*
Repeatability
* Diffuse mode performance based on 90% reflectance white test card.
Tracking Feature
Factory Default
Settings
P/N 65448 rev. E
PIT16U
PIT26U
PIT46U
PIT66U
PBT16U
PBT26U
PBT46U
PBT66U
Fiber
™
Red 680 nm
Toggle to select the condition for which each output will conduct: when the target is present or when the target is absent.
Programmable OFF-delay pulse stretcher: 0, 2, 5, 10, 15, 20, 30, 40, 60, 80, or 100 milliseconds
Analog Outputs: OFF-delay acts as a smoothing function
Discrete Output: Raw signal value or % excess signal
Analog Output: Raw signal value or analog value (0-10V dc or 4-20 mA)
Sets Output 2 to identical settings as Output 1; Output 2 settings can then be revised as desired. (See Advanced Setup procedure,
page 11.)
The following settings are preset at the factory; revert sensor to factory defaults using Advanced Setup procedure (page 11).
• Light operate (L)
• No OFF-delay (t 0)
• Raw signal value (1234)
100 mm
300 mm
600 mm
100 mm
175 mm
Super High-Speed (SHS)
Analog and Discrete Outputs
20 mm
30 mm
6 mm
50 µs
25 µs
Green 525 nm
Overview
100 mm
180 mm
40 mm
12 mm
30 mm
55 mm
**
9 mm
• Output 1 displayed
• High Speed (HS); 200 µs response
Red 680 nm
1000 mm
150 mm
550 mm
175 mm
250 mm
Programming Options
30 mm
10 mm
50 mm
High-Speed (HS)
200 µs
50 µs
Green 525 nm
100 mm
180 mm
40 mm
12 mm
30 mm
55 mm
**
9 mm
Red 680 nm
1000 mm
1700 mm
250 mm
100 mm
250 mm
400 mm
55 mm
18 mm
High-Power (HP)
• Maximum power setting
• Analog: full scale
• Discrete: switchpoint positioned at middle of range
Banner Engineering Corp.
75 µs
1 ms
www.bannerengineering.com • Tel: [phone]
Figure 1. D10 features
Green 525 nm
160 mm
280 mm
13 mm
55 mm
20 mm
42 mm
80 mm
3 mm
dynamic
static
Red 680 nm
1200 mm
2400 mm
400 mm
150 mm
300 mm
475 mm
For emitter and receiver port
locations, see page 11.
Super High-Power (SHP)
90 mm
30 mm
•
Minneapolis, MN U.S.A.
Output Select
Indicators
4-Digit
Display
Light/Dark
Operate, Clock
and Lock Icons
Programming
Push Buttons
Output
Indicators
2.5 ms
100 µs
Green 525 nm
180 mm
320 mm
100 mm
3.5 mm
16 mm
70 mm
25 mm
60 mm