9473PC 3M, 9473PC Datasheet - Page 9

• Manufacturer Part Number: 9473PC
• Description: TAPE, FOAM, CLEAR, 2INX60YD
• Manufacturer: 3M

Specifications of 9473PC

• Roll Length: 60yard
• Leaded Process Compatible: No
• Pack Quantity: 1
• Tape Type: Foam
• Width: 2"
• Color: Clear
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

3M
Application Techniques
Clean: Most substrates are best prepared by cleaning with a 50:50 mixture of isopropyl alcohol (IPA*) and
water prior to applying 3M™ VHB™ Tapes.
Pressure: Bond strength is dependent upon the amount of adhesive-to-surface contact developed. Firm
application pressure develops better adhesive contact and helps improve bond strength. Typically, good surface
contact can be attained by applying enough pressure to insure that the tape experiences approximately 15 psi
(100 kPa) pressure. Either roller or platen pressure can be used. Note that rigid surfaces may require 2 or 3 times
that much pressure to make the tape experience 15 psi.
Temperature: Ideal application temperature range is 70°F to 100°F (21°C to 38°C). Pressure sensitive
adhesives use viscous flow to achieve substrate contact area. Minimum suggested application temperatures:
Time: After application, the bond strength will increase as
the adhesive flows onto the surface (also referred to as “wet out”).
At room temperature approximately 50% of ultimate bond
strength will be achieved after 20 minutes, 90% after 24 hours
and 100% after 72 hours. This flow is faster at higher temperatures
and slower at lower temperatures. Ultimate bond strength can be
achieved more quickly (and in some cases bond strength can be
increased) by exposure of the bond to elevated temperatures
(e.g. 150°F [66°C] for 1 hour). This can provide better adhesive
wetout onto the substrates. Abrasion of the surfaces or the use of
primers/ adhesion promoters can also have the effect of increasing
bond strength and achieving ultimate bond strength more quickly.
™
Exceptions to the general procedure that may require additional surface preparation include:
• Heavy Oils: A degreaser or solvent-based cleaner may be required to remove heavy oil or grease from a
• Abrasion: Abrading a surface, followed by cleaning with IPA/water, can remove heavy dirt or oxidation
• Adhesion Promoters: Priming a surface can significantly improve initial and ultimate adhesion to many
• Porous surfaces: Most porous and fibered materials such as wood, particleboard, concrete, etc. need to be
• Unique Materials: Special surface preparation may be needed for glass and glass-like materials, copper and
Refer to 3M Technical Bulletin “Surface Preparation for 3M™ VHB™ Tape Applications” for additional
details and suggestions. (70-0704-8701-5)
*Note: These cleaner solutions contain greater than 250 g/l of volatile organic compounds (VOC). Please
• 50°F (10°C): 3M™ VHB™ Tapes 4950, 5952, 4910, 4952, 4611, 4622 families.
• 60°F (15°C): 3M™ VHB™ Tapes 4941, 4945 families.
• 32°F (0°C): 3M™ VHB™ Tape 4951 families.
Note: Initial tape application to surfaces at temperatures below these suggested minimums is not
To obtain good performance with all 3M™ VHB™ Tapes, it is important to ensure that the surfaces are dry
and free of condensed moisture.
VHB
surface and should be followed by cleaning with IPA/water.
and can increase surface area to improve adhesion.
materials such as plastics and paints.
sealed to provide a unified surface.
copper containing metals, and plastics or rubber that contain components that migrate (e.g. plasticizers).
recommended because the adhesive becomes too firm to adhere readily. However, once properly
applied, low temperature holding is generally satisfactory.
consult your local Air Quality Regulations to be sure the cleaner is compliant. When using solvents,
be sure to follow the manufacturer’s precautions and directions for use when handling such materials.
™
Tapes
- 9 -
100
80
60
40
20
0
20 MIN
PERCENT OF FULL BOND
1 HOUR
ROOM TEMP
Bond Typical Build vs. Time
24 HOURS
50°F
150°F or ABRADE
72 HOURS