RSC-HD0M60 CARLO GAVAZZI, RSC-HD0M60 Datasheet - Page 2

• Manufacturer Part Number: RSC-HD0M60
• Description: Motor Controller
• Manufacturer: CARLO GAVAZZI

Specifications of RSC-HD0M60

• Current Limit Max: 180mA
• Supply Voltage Max: 32VDC
• Controller Features: Soft Start, Linear Ramp, Multivoltage
• Supply Voltage Min: 10VDC
• Approval Bodies: CE
• Current Limit Min: 30mA
• Supply Voltage Range: 10VDC To 32VDC
• For Use With: -000 Mm

Output Specifications, Output Module
General Specifications, Output Module
Operational voltage range
Line to line
Non-rep. voltage
Varistor voltage
CE-marking
Rated operational current
Off-state leakage current
On-state voltage drop
I
Critical dI/dt
Non-rep. surge current
2
RSC 4-HD.M60/RSO22..., RSO4...., RSO60...
Control Input Specifications
Control voltage range
Ramp up function
Ramp down function
Input current
Adjust. starting torque
Adjust. ramp up time
Adjust. ramp down time
Response time
(input to trigger outputs)
Time to initialize after powerloss
Operation Diagram
2
t for fusing t=1-10 ms
AC 1
AC 3
t=20 ms
Motor
voltage
Starting
torque
Soft starting
Ramp up
time
Ramp down
time
Soft stopping
RSO 22...
150 to 250 VACrms
1200 V
275 VAC
Yes
RSO ..10
16 Arms
3 Arms
≤ 10 mArms
≤ 1.6 Vrms
≤ 130 A
≥ 50 A/µs
160 A
10 to 32 VDC
≥ 8 VDC
≤ 3 VDC
≤ 1 mA @ 32 VDC
10 to 75%
0.5 to 30 s
0.5 to 30 s
≤ 50 ms
< 300 ms
p
p
2
s
Power supply OFF
RSO ..25
25 Arms
5 Arms
≤ 10 mArms
≤ 1.6 Vrms
≤ 310 A
≥ 50 A/µs
250 A
RSO 40...
220 to 420 VACrms
1200 V
420 VAC
Yes
p
2
s
p
Insulation Control Module
Rated insulation voltage
Accessories
Heatsinks
Fuses
Temperature limit switch
Power supply
Mode of Operation
The control module RSC-
HD0M60 is used with the out-
put module RSO.. to achieve
soft starting and soft stopping
of 3-phase induction motors.
Soft starting is achieved by
increasing the motor voltage
in accordance with the setting
of the ramp up time poten-
tiometer within the range of
0.5 to 30 s. Soft stopping is
achieved by decreasing the
motor voltage in accordance
with the setting of the ramp
down
within the range of 0.5 to 30 s.
Input to trigger outputs
Specifications are subject to change without notice (30.06.1999)
RSO ..50
50 Arms
15 Arms
≤ 10 mArms
≤ 1.6 Vrms
≤ 1800 A
≥ 50 A/µs
600 A
time
p
RSO 48...
400 to 510 VACrms
1200 V
510 VAC
Yes
2
s
potentiometer
p
RSO ..90
90 Arms
30 Arms
≤ 25 mArms
≤ 1.8 Vrms
≤ 5000 A
≥ 50 A/µs
1000 A
For further information refer
to “General Accessories”.
p
The starting torque poten-
tiometer makes it possible to
adjust the starting level of the
motor voltage to a value at
which the motor starts to ro-
tate immediately when soft
starting is initiated. When the
motor is fully operating, an
output signal appears which
can be used to connect a by-
passing relay or contactor in
parallel to the output module,
thus limiting the need for cool-
ing.
Note: Only delta/star without
neutral.
≥ 4000 VACrms
2
s
RSO 60...
400 to 625 VACrms
1600 V
625 VAC
Yes
RSO ..110
110 Arms
40 Arms
≤ 25 mArms
≤ 1.8 Vrms
≤ 11250 A
≥ 50 A/µs
1500 A
p
p
2
s