0779185-401 VEEDER ROOT, 0779185-401 Datasheet - Page 132

• Manufacturer Part Number: 0779185-401
• Description: Electromechanical Totalizing Counter
• Manufacturer: VEEDER ROOT

Specifications of 0779185-401

• No. Of Digits / Alpha: 5
• Digit Height: 4mm
• Power Consumption: 5VA
• Operating Temperature Range: 0°C To +50°C
• Mounting Type: Rear
• Counter Supply Voltage: 115VAC
• Lead Free Status / RoHS Status: na

R
O
N
E
L
E
C
T
C
I
5
M
R
S
T
E
M
I
T
E
R
S
I
5.38
The CX100 is a solid state repeat cycle timer that will alternately turn an
output on and off as long as power is applied to the unit. The CX100 is
a microprocessor based timer with digital setting for greater setting
accuracy than can be achieved with analog style repeat cycle timers. In
addition to its greater setting accuracy, the CX100 timer is fully
programmable to provide a number of time ranges and operating
modes in one unit.
The ON and OFF time ranges are individually programmable for four
time ranges from 199.99 seconds to 199 hours and 59 minutes. The
CX100 timer is also programmable to have the ON time first instead of
the OFF time first and to reset or non-reset on power interruption. The
time ranges and the operating characteristics of the unit are pro-
grammed using 7 miniature rocker switches located inside the unit
housing.
Housed in standard CYCL-FLEX
programming changes, and service
4 1/2 digit (19999) liquid crystal display - .5 inch high
Annunciators (right of the display) flash to indicate ON time cycle
and are constantly on to indicate OFF time cycle
Two socket mount 10 amp output relays - one performs ON/OFF
cycle switching and the other is a set of instantaneous contacts that
energize when power is applied to the start input and do not
deenergize until power is disconnected from the start input
Time inhibit input allows timing function to be stopped without
resetting the unit
Non-volatile memory data retention
EAGLE SIGNAL
Electronic Timers
VEEDER-ROOT • EAGLE SIGNAL • DYNAPAR
®
enclosure for easier removal,
brand
SPECIFICATIONS
Time Ranges:
Operating Voltage/Frequency:
Setting Accuracy:
Repeat Accuracy:
Reset Time: 30 ms following voltage removal from simulated clutch input
Power on Response: 300 ms maximum after voltage applied to terminal 11
Operating Temperature: +32° to +140°F (0° to +60°C)
Output Rating: Relay: 10 amp (resistive), 120 VAC
Vibration: Unit function is unaffected by 2.5
Static Discharge: Unit function is unaffected by a constant 3600 volt peak,
Approvals: UL Recognition E96337
CX100 Repeat Cycle Timer
CX100 Repeat Cycle Timer
CX100 Repeat Cycle Timer
A6 - 120 VAC, 50/60 Hz
B6 - 240 VAC ,50/60 Hz
(CR1)
Mechanical Life: 20 million operations
Electrical Life: contingent upon controlled load
tude in both directions of the perpendicular mounting axes imposed from
10 to 100 Hz
60 Hz discharge applied to the grounded front plate at a relative humidity
of less than 25%
CSA Certification LR26861
0.001% of setting or 35 ms, whichever is larger (0° to 60°C)
Continuously runs
cycles with
independently
settable on/off ratio
0.05% or 50 ms, whichever is larger (0° to 60°C)
199 Min.: 59 Sec.
199 Min.: 59 Sec.
199 Min.: 59 Sec.
199 Hr.: 59 Min.
199 Hr.: 59 Min.
199 Hr.: 59 Min.
Maximum
Maximum
Maximum
199.99 Sec.
199.99 Sec.
199.99 Sec.
1999.9 Sec.
1999.9 Sec.
1999.9 Sec.
Range
Range
Range
Minimum
Minimum
Minimum
Setting
Setting
Setting
.01 Sec.
.01 Sec.
.01 Sec.
.1 Sec.
.1 Sec.
.1 Sec.
1 Sec.
1 Sec.
1 Sec.
1 Min.
1 Min.
1 Min.
G
sinusoidal vibration magni-
®
®
®
RECOGNIZED
RECOGNIZED
RECOGNIZED
CERTIFIED
CERTIFIED
CERTIFIED
®
®
®