SNAP-PAC-S1-W OPTO 22, SNAP-PAC-S1-W Datasheet - Page 3

• Manufacturer Part Number: SNAP-PAC-S1-W
• Description: Programmable Controller Wireless
• Manufacturer: OPTO 22

Specifications of SNAP-PAC-S1-W

• Accessory Type: Programmable Automation Communication
• Signal Input Type: Ethernet, RS-232
• Rohs Compliant: Yes
• For Use With: SNAP PAC System
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

SNAP PAC S-Series Controllers
Technical Specifications
© 2006–2009 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
Processor
Memory
Removable storage
Backup battery
Ethernet Communication
(host and I/O)
Serial Communication
I/O unit compatibility
Power requirements
Operating temperature
Storage temperature
Humidity
Software
Other features
Ethernet-based I/O units
Serial-based I/O units
PAC Project Basic
PAC Project Professional
Total RAM
Battery-backed RAM
Flash
Range (serial multidrop)
SNAP-PAC-S1
SNAP-PAC-S2
SALES 800-321-6786 • 951-695-3000 • FAX [phone] • [e-mail] • SUPPORT 800-835-6786 • 951-695-3080 • FAX [phone] • [e-mail]
RS-232 serial
RS-485 serial
266 MHz 32-bit ColdFire
32 MB (16 MB available for PAC Control strategy)
8 MB
16 MB (7.5 MB available for PAC Control strategy; 4 MB available for file storage)
(Models manufactured November 2008 and later; requires firmware R8.4 or
higher) MicroSD card slot: supports MicroSD card up to 2 GB maximum
SNAP-PAC-S1: User-replaceable 3.6-volt TL 5242 /W lithium, 10-year minimum
power-off data retention (replacement part number: G4BATT32)
SNAP-PAC-S2: Rechargeable (recharges whenever the brain has power), 1-year
power-off data retention
Two independent 10/100 Mbps Ethernet network interfaces (RJ-45 connectors).
Each interface has a separate IP address (separate subnet).
For Opto 22 devices, 32 stations maximum between repeaters (controller plus 31
serial I/O units); up to 3000 ft (914 m) between repeaters
Two RS-232 serial ports (one DB-9 and one pluggable connector); one port has
full handshaking. PPP is supported only on port 0.
One RS-485 serial port (pluggable connector); two-wire RS-485; optional mistic
signal interrupts
Four serial ports that can be used as general purpose ports or for serial I/O units;
each port is software configurable as either RS-232 (Tx, Rx, COM, DTR, DCD,
RTS, CTS) or as RS-485 (2-wire, 4-wire, optional termination, optional biasing);
optional mistic signal interrupts
Opto 22 SNAP PAC R-series, SNAP PAC EB-series, SNAP SIO, SNAP EIO, and
SNAP UIO brains
SNAP PAC SB-series, Serial B3000, SNAP-BRS, B100/B200, mistic remote
bricks (G4D16R, G4D32RS, G4A8R)
8–32 VDC ±0.5, 10 VA maximum
(SNAP-PAC-S1 controllers with serial numbers below 500,000 use 8–24 VDC)
0
-40
0% to 95% relative humidity, non-condensing
Includes programming, HMI software, and configuration software; included with
purchase of controller.
PAC Project Basic plus OPC 2.0-compliant OPC server, OptoControl strategy and
OptoDisplay project importing, support for serial mistic I/O units, and Ethernet link
redundancy support.
Multiple protocol support including TCP/IP, FTP, SNMP v2.0c (with firmware 8.2a),
Modbus/TCP, EtherNet/IP™, and OptoMMP™.
Real-time clock
FTP server/client with file system (in RAM and in removable storage)
Ethernet link redundancy or network segmenting
o
C to 60
o
C to 85
o
C
o
C
®
5475 with integrated floating-point unit (FPU)
Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com
PAGE
3