WV408-2000.V1 EUROTHERM CONTROLS, WV408-2000.V1 Datasheet - Page 4

• Manufacturer Part Number: WV408-2000.V1
• Description: Isolating Signal Conditioner
• Manufacturer: EUROTHERM CONTROLS

Specifications of WV408-2000.V1

• Width: 12.7mm
• Isolation Input: Isolated
• Output Accuracy: ±0.05% Of FS
• Signal Input Type: Selectable Current Or Voltage
• Supply Voltage: 24VDC
• Configuration Setup: DIP Switch
• Iso-amp Mounting Type: DIN Rail
• Rohs Compliant: NA
• Dc / Dc Converter O/p Type: Adjustable
• Display Alarm Type: 2 Relay
• Input Accuracy: ±0.015% Of FS

For more information contact your local representative:
COMMON SPECIFICATIONS
Electrical
Input Range
Output (Conditioners)
Limit Alarms
Drive
Compliance
Input Accuracy
Output Accuracy
Response Time
Stability
Common Mode Rejection 120dB @ DC; >90dB @ 60Hz or
Isolation
ORDERING INFORMATION
Limit Alarms
WV108-2000
WV108-2001
WV118-2000
WV118-2001
WV128-2000
WV128-2001
WV168-2000
WV168-2001
Signal Conditioners
WV408-2000
WV418-2000
WV428-2000
WV438-2000
WV448-2000
WV468-2000
WV478-2000
741-F Miller Drive, Leesburg, Virginia 20175, Phone [phone], Fax [phone], [e-mail], www.eurotherm.com
A c t i o n I n s t r u m e n t s • B a r b e r - C o l m a n •
DC Input Limit Alarm
DC Input Limit Alarm w/ Latching
Relays and Reset Switch
RTD Input Limit Alarm
RTD Input Limit Alarm w/ Latching
Relays and Reset Switch
Thermocouple Input Limit Alarm
Thermocouple Input Limit Alarm w/
Latching Relays and Reset Switch
AC Input Limit Alarm
AC Input Limit Alarm w/ Latching
Relays and Reset Switch
DC Input Isolator
RTD Input Signal Conditioner
Thermocouple Input Signal Conditioner
Potentiometer Input Signal Conditioner
Bridge Input Signal Conditioner
AC Input Signal Conditioner
Frequency Input Signal Conditioner
Selection by DIP switch (where
applicable)
0 to 10V or 0 to 20mA
2 SPDT relays, 5A at 120Vac
10mA
20V @ 20mA (1k ohms max.)
±0.015% of FS
±0.05% of FS
100mSec (10% to 90%)
±100ppm/°C (±0.01%)
higher
1800VDC or peak AC between
input, output & power
Physical
Size (DIN rail case)
Isolators
Limit Alarms/RTD/Bridge
Comm Interface/Pwr Supply 0.89” (22.6mm) wide
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
Agency Approvals
Accessories
WVC16-2000
C650-2000
WV905
H902
H910
H915
MD03
MB03
C620
E u r o t h e r m C h e s s e l l • E u r o t h e r m C o n t r o l s
Refer to individual data sheets for
more detailed information.
Ultra SlimPak II Communications Interface
Software CD and Serial Cable
24VDC Power Supply (0.5 Amp)
24VDC Power Supply (0.2 Amp)
24VDC Power Supply (1 Amp)
24VDC Power Supply (2.3 Amp)
TS35 x 7.5 DIN rail (2 meters)
End Bracket for MD03
Optional Custom Factory Calibration
©2004 Eurotherm Controls Incorporated. All rights reserved. Every
effort has been taken to ensure the accuracy of this specification.
However, in order to maintain our technological lead we are con-
tinuously improving our products which could, without notice, result
in amendments or omissions to these specifications. We cannot
accept responsibility for damage, injury, or loss expenses resulting from
this document.
0.5” (12.7mm) wide
0.69” (17.5mm) wide
0°C to +60°C (32ºF to 140°F)
-25°C to +85°C (-13ºF to 185°F)
15% to 95% RHNC @ 45°C
90% RHNC @ 60°C for 24hrs
EN50081-1, EN50082-2, EN61010
pending (EMC & Safety) CSA
C22.2, No. 0-M91142-M1987
pending; UL508 pending
March 2004
HA136735