HFBR-1537Z Avago Technologies US Inc., HFBR-1537Z Datasheet - Page 10

• Manufacturer Part Number: HFBR-1537Z
• Description: FIBER OPTIC TRANSCEIVER MODULE
• Manufacturer: Avago Technologies US Inc.

Specifications of HFBR-1537Z

• Msl: MSL 4 - 72 Hours
• Peak Reflow Compatible (260 C): Yes
• Leaded Process Compatible: Yes
• Wavelength: 650nm
• Spectral Bandwidth: 21nm
• Voltage - Forward (vf) Typ: 2.1V
• Current - Dc Forward (if): 60mA
• Voltage - Dc Reverse (vr) (max): 3V
• Capacitance: 60pF
• Connector Type: Versatile Link
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

10
Electrical/Optical Characteristics 0 to 70°C; 5.25 V ≥ V
Notes:
10. If there is no input optical power to the receiver (no transmitted signal) electrical noise can result in false triggering of the receiver. In typical
Parameter
AC Responsivity 1 mm POF
AC Responsivity 200 µm HCS
RMS Output Noise
Equivalent Optical Noise Input
Power, RMS - 1 mm POF
Equivalent Optical Noise Input
Power, RMS - 200 µm HCS
Peak Input Optical Power -
1 mm POF
Peak Input Optical Power -
200 µm HCS
Output Impedance
DC Output Voltage
Supply Current
Electrical Bandwidth
Bandwidth * Rise Time
Electrical Rise Time, 10-90%
Electrical Fall Time, 90-10%
Pulse Width Distortion
Overshoot
1. 1.6 mm below seating plane.
2. The signal output is an emitter follower, which does not reject noise in the power supply. The power supply must be filtered as in Figure 1.
3. Typical data are at 25°C and V
4. Pin 1 should be ac coupled to a load ≥ 510 Ω with load capacitance less than 5 pF.
5. Measured with a 3 pole Bessel filter with a 75 MHz, -3dB bandwidth.
6. The maximum Peak Input Optical Power is the level at which the Pulse Width Distortion is guaranteed to be less than the PWD listed under
7. 10 ns pulse width, 50% duty cycle, at the 50% amplitude point of the waveform.
8. Percent overshoot is defined at:
9. Pins 5 and 8 are primarily for mounting and retaining purposes, but are electrically connected. It is recommended that these pins be con-
Test Condition. P
MBd (for both POF and HCS input conditions).
nected to ground to reduce coupling of electrical noise.
applications, data encoding and error detection prevent random triggering from being interpreted as valid data. Refer to Application Note
1066 for design guidelines.
R,Max
is given for PWD = 5 ns for designing links at ≤ 50 MBd operation, and also for PWD = 2 ns for designing links up to 125
CC
= +5 Vdc.
Symbol
P
P
PWD
R
R
BW
V
N,RMS
N,RMS
Z
I
P,APF
P,HCS
P
P
V
t
t
CC
NO
O
O
r
f
R
R
E
CC
≥ 4.75 V; power supply must be filtered (see Figure 1, Note 2).
–––––––––––– × 100%
Min.
(V
1.7
4.5
0.8
65
PK
- V
V
100%
100%
0.46
0.41
Typ.
- 39
125
)
-42
3.9
7.9
1.8
3.3
3.3
0.4
30
9
4
Max.
11.5
0.69
-5.8
-6.4
-8.8
-9.4
-36
-40
6.5
2.6
6.3
6.3
1.0
15
mV/µW
mV/µW
mV
Hz * s
dBm
dBm
dBm
dBm
dBm
dBm
MHz
Unit
mA
ns
ns
ns
Ω
%
V
RMS
-3 dB electrical
Test Condition
P
P
P
P
R
R
R
R
5 ns PWD
2 ns PWD
5 ns PWD
2 ns PWD
P
650 nm
50 MHz
= -10 dBm
= -10 dBm
= -10 dBm
= -10 dBm
R
peak
peak
peak
peak
= 0 µW
Note 4
Note 5
Note 5
Note 5
Note 6
Note 6
Note 4
Note 7
Note 8
Note