ACPL-P454-020E Avago Technologies US Inc., ACPL-P454-020E Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/0/86/avago_technologies_us_inc__sml.jpg)
ACPL-P454-020E
Manufacturer Part Number
ACPL-P454-020E
Description
Optocoupler(1MBd),LF+UL
Manufacturer
Avago Technologies US Inc.
Datasheet
1.ACPL-P454-520E.pdf
(9 pages)
Specifications of ACPL-P454-020E
Voltage - Isolation
5000Vrms
Number Of Channels
1, Unidirectional
Current - Output / Channel
8mA
Propagation Delay High - Low @ If
500ns @ 12mA
Current - Dc Forward (if)
25mA
Input Type
DC
Output Type
Open Collector
Mounting Type
Surface Mount
Package / Case
SO-6
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Package Characteristics
Over recommended temperature (T
*
Notes:
1. Derate linearly above 70°C free-air temperature at a rate of 0.8 mA/°C.
2. Derate linearly above 70°C free-air temperature at a rate of 1.6mA/°C.
3. Derate linearly above 70°C free-air temperature at a rate of 0.9 mW/°C.
4. Derate linearly above 70°C free-air temperature at a rate of 2.0 mW/°C.
5. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current (I
6. Device considered a two-terminal device: Pins 1 and 3 shorted together and Pins 4, 5 and 6 shorted together.
7. Under TTL load and drive conditions: Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dV
8. Under IPM (Intelligent Power Module) load and LED drive conditions: Common mode transient immunity in a Logic High level is the maximum
9. The 1.9 k: load represents 1 TTL unit load of 1.6 mA and the 5.6 k: pull-up resistor.
10. The R
11. Use of a 0.1 PF bypass capacitor connected between pins 4 and 6 is recommended.
12. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage t 4500 V
13. The difference between t
Figure 1. DC and Pulsed Transfer Characteristics.
7
Parameter
Input-Output Momentary
Withstand Voltage*
Input-Output Resistance
Input-Output Capacitance
10
The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage
rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable).
leading edge of the common mode pulse, V
immunity in a Logic Low level is the maximum tolerable (negative) dV
that the output will remain in a Logic Low state (i.e., VO < 0.8 V).
tolerable dV
V). Common mode transient immunity in a Logic Low level is the maximum tolerable dV
signal,V
current limit, I
age detection current limit, I
Propagation Delay Specifications section).
5
0
0
T = 25 ˚C
V
A
CC
L
= 5.0 V
= 20 k:, C
CM
V
O
, to assure that the output will remain in a Logic Low state (i.e., V
CM
- OUTPUT VOLTAGE - V
I-O
/dt on the leading edge of the common mode pulse, VCM, to assure that the output will remain in a Logic High state (i.e., V
d 5 PA); each optocoupler under ACPL-W454 is proof tested by applying an insulation test voltage ≥ 6000 V
L
= 100 pF load represents an IPM (Intelligent Power Mode) load.
10
PLH
I-O
and t
I = 5 mA
40 mA
35 mA
30 mA
25 mA
20 mA
15 mA
10 mA
F
≤ 5 μA).
Symbol
V
R
C
PHL
ISO
I-O
I-O
20
, between any two ACPL-W454/P454 parts under the same test condition. (See Power Inverter Dead Time and
A
= 0°C to 70°C) unless otherwise specified. All typicals at T
CM
Min.
3750
5000 (For “ACPL-W454)
, to assure that the output will remain in a Logic High state (i.e., V
Figure 2. Current Transfer Ratio vs. Input Current.
1.5
1.0
0.5
0.0
0
Typ.
10
0.6
2 4 6 8 10 12 14 16 18
12
I
F
- INPUT CURRENT - mA
Max.
CM
/dt on the trailing edge of the common mode pulse signal, V
O
NORMALIZED
I
V
V
T
< 1.0 V).
F
CC
Units
Vrms
:
pF
O
A
= 16 mA
= 25 ˚C
= 0.4 V
= 5.0 V
20 22 24 26
O
Test Conditions
RH d 50%, t = 1 min, T
V
f = 1 MHz; V
CM
), to the forward LED input current (I
I-O
/dt on the trailing edge of the common mode pulse
= 500 Vdc
Figure 3. Input Current vs. Forward Voltage.
0.001
1000
0.01
100
I-O
1.0
0.1
10
1.1
= 0 Vdc
RMS
O
1.2
V
> 2.0 V). Common mode transient
F
V
A
for 1 second (leakage detection
+
- FORWARD VOLTAGE - VOLTS
-
F
A
I
= 25°C
F
= 25°C.
1.3
RMS
1.4
F
Fig.
), times 100.
for 1 second (leak-
T = 25˚C
A
CM
CM,
1.5
/dt on the
Note
6,12
6
6
to assure
O
1.6
> 3.0