MGA-633P8-TR1G Avago Technologies US Inc., MGA-633P8-TR1G Datasheet
MGA-633P8-TR1G
Specifications of MGA-633P8-TR1G
Available stocks
Related parts for MGA-633P8-TR1G
MGA-633P8-TR1G Summary of contents
Page 1
... It is designed for optimum use from 450MHz up to 2GHz. The compact footprint and low profile coupled with low noise, high gain and high linearity make the MGA-633P8 an ideal choice as a low noise amplifier for cellular infrastructure for GSM and CDMA. For optimum performance at higher frequency from 1.5GHz to 2.3GHz, the MGA-634P8 is recommended, and from 2 ...
Page 2
Absolute Maximum Rating T =25°C A Symbol Parameter V Device Voltage, RF output to ground dd I Drain Current Input Power max ( [3] P Total ...
Page 3
Product Consistency Distribution Charts LSL Id Max:67 Min:39 Mean: Figure 900MHz, 5V, 54mA Mean = 54 LSL OIP3 Min:34 Mean: ...
Page 4
... L1 C1 RFin Figure 6. Demo Board Schematic Diagram Note: x The schematic is shown with the assumption that similar PCB is used for all MGA-633P8, MGA-634P8 and MGA-635P8. x Detail of the components needed for this product is shown in Table 1. Value Detail Part Number 100pF (Murata) GRM1555C1H101JD01E 33nH (Toko) ...
Page 5
... MGA-633P8 Typical Performance RF performance 25°C, Vdd = 5V 54mA, measured using 50ohm input and output board, unless otherwise stated. A OIP3 test condition 900 MHz, F RF1 0.5 0.4 0.3 0.2 0 Idd (mA) Figure 7. Fmin vs Idd 700MHz Idd(mA) Figure 10. Gain vs Idd at 5V Tuned for Optimum OIP3 and Fmin at 700MHz ...
Page 6
Idd(mA) Figure 14. OP1dB vs Idd at 5V Tuned for Optimum OIP3 and Fmin at 700MHz 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 500 650 ...
Page 7
... Frequency (MHz) Figure 19. Fmin vs Frequency and Temperature for Optimum OIP3 and Fmin at 5V 54mA Below is the table showing the MGA-633P8 Reflection Coefficient Parameters tuned for Maximum OIP3, Vdd = 5V, Idd = 54mA. Gamma Load position Frequency (GHz) Magnitude 0.50 0.53 ...
Page 8
... MGA-633P8 Typical Performance in Demoboard RF performance 25°C, Vdd = 5V, Rbias = 6.8kOhm, measured on demo board in Figure.5 with component list in A Table1 for 900 MHz matching, unless otherwise stated. 0.8 0.7 0.6 0.5 0.4 0.3 0.2 -40°C 25°C 0.1 85° 500 1000 Frequency (MHz) Figure 22 Frequency vs Temperature ...
Page 9
... MGA-633P8 Typical Performance in Demoboard RF performance °C, Vdd =5V, Rbias=6.8kOhm, measured on demo board in Figure.5 with component list in A Table1 for 900 MHz matching, unless otherwise stated Rbias (Kohm) Figure 28. Idd vs Rbias 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0 500 1000 Frequency (MHz) Figure 30 Frequency vs Idd ...
Page 10
... MGA-633P8 Typical Scattering Parameters, Vdd = 5V, Idd = 54mA S 11 Freq GHz Mag. Ang. 0.1 0.73 -45.42 0.5 0.25 -95.49 0.9 0.16 -119.26 1.0 0.15 -124.97 1.5 0.10 -142.55 1.9 0.07 -158.30 2.0 0.07 -162.64 2.5 0.05 177.70 3.0 0.03 162.14 4.0 0.01 -41 ...
Page 11
... Top View 0.60±0.050 Exp. DAP 0.35±0.050 0.25±0.050 Bottom View 11 Part Number Ordering Information * Part Number opt Ang. R MGA-633P8-BLKG n/50 -37 0.051 MGA-633P8-TR1G -17 0.0586 -15 0.0532 -13 0.0478 -7 0.0446 80.5 0.0644 98.7 0.0498 0.203 Ref. 0.000–0.05 0.75±0.05 Side View PIN #1 IDENTIFICATION R0.100 1.20± ...
Page 12
Recommended PCB Land Pattern and Stencil Design 2.20 1.75 0.00 0.80 0.50 0.25 0.45 0.30 R0.15 Land Pattern Combination of Land Pattern and Stencil Opening Note: 1. Recommended Land Pattern and Stencil Opening 2. Stencil thickness is 0.1mm (4 mils) ...
Page 13
Device Orientation REEL USER FEED COVER TAPE DIRECTION Tape Dimensions 10° Max A 0 DESCRIPTION CAVITY LENGTH WIDTH DEPTH PITCH BOTTOM HOLE DIAMETER PERFORATION DIAMETER PITCH POSITION CARRIER TAPE WIDTH THICKNESS COVER TAPE WIDTH TAPE ...
Page 14
Reel Dimensions – 7 inch 6.25mm EMBOSSED LETTERS LETTERING THICKNESS: 1.6mm SEE DETAIL "X" SLOT HOLE "b" SLOT HOLE(2x) 180° APART FRONT VIEW RECYCLE LOGO R10.65 R5.2 SLOT HOLE ‘b’ EMBOSSED RIBS RAISED: 0.25mm, WIDTH: 1.25mm ...