45LM58D BANNER ENGINEERING, 45LM58D Datasheet

45LM58D

Manufacturer Part Number

45LM58D

Description

Timing Logic Module

Manufacturer

BANNER ENGINEERING

Datasheet

1.45LM58D.pdf (6 pages)

Specifications of 45LM58D

Time Range

0.01s To 0.15s, 0.1s To 1.5s, 1s To 15s

Application

For timing logic functions

Function

Module, Logic

Logic Type

On⁄Off Delay

Technology

Photoelectric

Timing Adjustment

0.01 to 15 Sec.

Operating Temperature

–40°C to 70°C

Lead Free Status / Rohs Status

RoHS Exempt Product

Current page: 1 of 6
Download datasheet (227Kb)

Printed in USA

Operating Temperature

Timing Adjustments

Timing Repeatability

Useful Time Range

Response Time

LED Display

-40° to +70°C (-40° to +158°F)

Models 45LM58.. only: Two 15-turn clutched potentiometers with brass elements, accessible from

Models 45LM58.. only: Plus or minus 2% of the timing range (maximum); assumes conditions of

Models 45LM58.. only: Useful time range is from maximum time down to 5% of maximum. When the

Models 45LM58.. only: When the delay time is switched OFF, the card adds no measurable sensing

Models 45LM..D only: Seven-element LED display, visible through transparent top sensor cover. The

• Three plug-in modules are available:

• Models with selectable output timing offer the following timing logic functions (see

• Selectable timing ranges:

• Delay and hold time ranges may be individually selected, and times precisely set,

• Module allows sensor output to be set for normally-open or normally-closed

• Models with signal strength display give a precise indication of excess gain; see

page 2 or 3 for descriptions):

using 15-turn adjustment potentiometers. Delay or hold time may also be disabled

(zero seconds).

operation

page 4 for more information. Valuable for sensor setup and alignment, for critical

evaluation of alternative sensing schemes, and for close monitoring of sensing

performance over time (e. g., dirt build-up on lenses or progressive misalignment).

45LM Series Modules

Plug-in Logic and Display Modules for Q45 Series Photoelectric Sensors

0.01 to 0.15 seconds

- ON-delay

- OFF-delay

- ON- and OFF-delay

- Retriggerable one-shot

- Non-retriggerable one-shot

- Delayed one-shot

Model

45LM58

45LM58D

45LMD

more LEDs that are lit, the stronger is the received light signal; three LEDs lit is

equivalent to an excess gain of about 1x (see page 4).

outside at the top of sensor, beneath an o-ring sealed polycarbonate cover.

constant temperature and power supply.

timing potentiometer is set fully counterclockwise, time will be approximately 5%

of maximum.

response time.

Specifications

07/04

Selectable output timing

Selectable output timing, plus signal strength display

Signal strength display, only (no programmable functions)

Functions

0.1 to 1.5 seconds

Features

- ON-delayed one-shot

- Repeat cycle timer

- Limit timer

- Rate sensor

- Flip-flop (alternate action)

1 to 15 seconds

P/N 63416 rev. A

Related parts for 45LM58D

45LM58D Summary of contents

Page 1

... Three plug-in modules are available: Model Functions 45LM58 Selectable output timing 45LM58D Selectable output timing, plus signal strength display 45LMD Signal strength display, only (no programmable functions) • Models with selectable output timing offer the following timing logic functions (see page for descriptions): ...

Page 2

... Series Modules Setting Output Timing Function Models 45LM58 and 45LM58D (with signal strength display) may be set for one or several output timing functions. In addition, three adjustable timing ranges are available (see page 3). Output Timing Function: ON-delay Switch 1 Switch 2 Switch 3 Other Settings ...

Page 3

... Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 Output Timing Function: ON-delayed one-shot Switch 1 Switch 2 Switch 3 Other Settings OFF ON OFF Output Timing Function: Repeat cycle timer Switch 1 Switch 2 Switch 3 Other Settings OFF OFF ON Output Timing Function: Limit timer Switch 1 ...

Page 4

... Series Modules Measuring Excess Gain and Contrast The seven-element LED array, available on models 45LM58D and 45LMD, may be used to measure the excess gain and contrast in any sensing situation and during sensor installation and maintenance. Excess gain is a measurement of the amount of light energy falling on the receiver of a photoelectric sensor over and above the minimum amount necessary to operate the sensor’ ...

Page 5

... Figure 5. Insert a small screwdriver into the slot and lift the black cover to remove. Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 Removing and Installing the Plug-In Modules To remove or install any of the 45LM modules (done through the top of the sensor), perform the following steps: 1) Remove all power from the sensor and load ...

Page 6

... Banner Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection. WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period ...

Related keywords

45LM58D datasheet
45LM58D data sheet
45LM58D pdf datasheet
45LM58D component
45LM58D part
45LM58D distributor
45LM58D RoHS
45LM58D datasheet download