ADS512101 Freescale Semiconductor, ADS512101 Datasheet

KIT, DEVELOPMENT SYSTEM, MPC5121E

ADS512101

Manufacturer Part Number
ADS512101
Description
KIT, DEVELOPMENT SYSTEM, MPC5121E
Manufacturer
Freescale Semiconductor
Datasheet

Specifications of ADS512101

Mcu Supported Families
MPC51xx
Tool / Board Applications
Microcontroller
Svhc
No SVHC (15-Dec-2010)
Development Tool Type
Development Kit
Kit Contents Descriptive
ADS512101 Unit (with SN & MAC
Silicon Manufacturer
Freescale
Core Architecture
Power Architecture
Core Sub-architecture
Power Architecture
Silicon Core Number
MobileGT, MPC5xx
Silicon Family Name
Qorivva
Kit Contents
Board
Rohs Compliant
No
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Thank you for purchasing an ADS512101 Advanced Development System for the MPC5121e. This
document guides you through getting a quick start with the ADS512101. It does NOT replace all the
documentation provided on the CD, but gives you a good starting point.
Contents
Verify the following is included in the ADS512101 kit:
Power:
The ADS512101 can be powered by either the 5 Volt wall cube power supply included with
this kit or a low power ATX power supply. If the 5 Volt wall cube power supply is used PCI
and other peripherals requiring 12 Volts will NOT function.
WARNING:
P1, 5V Standby. Remove the jumper if using an ATX power supply.
Host Communications:
Connect the null modem cable from the serial port of the ADS512101 (see illustration) to the
host computer. The host communication port should be set to 115.2K Baud, 8bit data, no
parity, 1 stop bit, no flow control. Start the terminal program being used.
Boot Up:
Assemble the power supply with the correct adapter and connect it to local power and the
ADS512101. Power LED #1 will light. To launch U-Boot in ADS512101, push the power on
switch SW1 (see illustration).
Linux (Freescale):
After U-Boot is running, Freescale’s Linux BSP has been pre-loaded and will automatically
boot, if you do not hold down any key. Linux takes several minutes to load and boot.
Linux is ready when its prompt appears, -sh-2.05b# . Refer to the User Manual included on
the CD for U-Boot commands and Freescale’s Linux information. The User Manual also
provides a complete description of all user interfaces for connectors, jumpers, switches and
LEDs. (Freescale’s Spinning Car graphic demo has also been pre-loaded. To launch this
demo at the Linux prompt type demoloop).
Warranty:
In the next day or two take a few moments to complete the enclosed warranty information.
We need this information to assure you are contacted for future software upgrades or
ADS512101 notifications
ADS512101 unit (with SN & MAC address label)
Power Supply, PSA05R-050-R & Adapters RPBAG-R
Null Modem Cable
CodeWarrior Develop Suite CDs
STx CD (with SN & MAC address label)
Literature Packet
Packing List, Warranty & Quick Start Guide
:
STx, Silicon Turnkey Express, 440-461-4700, 749 Miner Road, Highland Hts, OH 44143
To use the 5 Volt wall cube power supply a jumper MUST be placed on
Quick Start Guide
www.silicontkx.com
ADS512101

Related parts for ADS512101

ADS512101 Summary of contents

Page 1

... Thank you for purchasing an ADS512101 Advanced Development System for the MPC5121e. This document guides you through getting a quick start with the ADS512101. It does NOT replace all the documentation provided on the CD, but gives you a good starting point. Contents : Verify the following is included in the ADS512101 kit: ADS512101 unit (with SN & ...

Page 2

... Serial UART0 Connector Installing U-Boot: The ADS512101 has a protected back up FLASH memory for U-Boot. If U-Boot should become corrupt for any reason, U-Boot can be re-installed. Please follow these instructions to re-flash U-Boot to the main memory. 1 – Remove power from the ADS512101 2 – Install a jumper on the ‘Back Up Flash’ Header – ...

Related keywords