ERJT06J272V Panasonic, ERJT06J272V Datasheet

Page 1

...

Page 2

... Ambient Temperature (deg.C) Figure 1 Rated value When used at ambient temperature above 70 deg.C, power rating shall be determined in accordance with Figure 1. Panasonic Electronic Devices Co., Ltd. Spec. No 0.50+/-0.20 0.60+/-0.10 Operating temperature range : -55 to 155 deg.C ...

Page 3

... The first two digits are the significant figures of resistance value, and the last figure shows the number of zero following in ohm. And decimal point is expressed by “R”. (5) Packaging Configuration Code Packaging Configuration V Taping (5000pcs/reel) PRODUCT SPECIFICATION FOR IMFORMATION 151-SRJ-ET0601A ERJT06 Rated value (E-24 (2) ( Anti-Pulse type Panasonic Electronic Devices Co., Ltd. Spec. No Explanation (4) (5) 2 ...

Page 4

... As far as there shall not designation especially, the following tests and measurement shall be operated under the following conditions. Normal temperature : 5 deg deg.C Normal humidity : Normal atmospheric pressure : 106 k Pa PRODUCT SPECIFICATION FOR IMFORMATION 151-SRJ-ET0601A ERJT06 Rated value Panasonic Electronic Devices Co., Ltd. Spec. No Explanation ...

Page 5

... AC 200V between substrate and termination for 1 minute. Resistors shall be facing down. After applying DC 200V to the resistor, insulation resistance shall be measured. Noise Noise shall be measured by RESISTOR NOISE TEST SET MODEL 315C by Quan-Tech Div. Max. V Panasonic Electronic Devices Co., Ltd. Spec. No. 11 Test Method (JIS-C5201-1) 6 –6 -R )x10 /R (t ...

Page 6

... Hz, and return traversing for 1 min. Solvent solution : Isopropyl alcohol (1) Dipping 10 +/- 1 hours, dry in room condition for 30 +/- 10 minutes. (2) Ultrasonic wave washing : 5 +/- 1 min. Dry in room condition for 30 +/-10 minutes. Panasonic Electronic Devices Co., Ltd. Spec. No. 11 Test Method (JIS-C5201-1) 1.4 1.2 1.4 (mm) 1.65 ...

Page 7

... The first two digits should be significant figures of resistance for E-24 series and the third one denotes number of zeros. Decimal point should be expressed by “.”. Panasonic Electronic Devices Co., Ltd. Spec. No. 11 Test Method (JIS-C5201-1) Time (min.) -55 +/-3 ...

Page 8

... Never exceed the rated power. When the product shall be used under special condition, be sure to ask us in advance. PRODUCT SPECIFICATION FOR IMFORMATION ERJT06 ! Notice for use Panasonic Electronic Devices Co., Ltd. Spec. No. 151-SRJ-ET0601A - 11 7 ...

Page 9

... If you need the notice by letter of “A preliminary judgement on the Laws of Japan foreign exchange and Foreign Trade control”, be sure to let us know. 13. Production site Country : Japan Plant : Panasonic Electronic Devices Fukui Co., Ltd. PRODUCT SPECIFICATION FOR IMFORMATION ERJT06 Panasonic Electronic Devices Co., Ltd. ...

Page 10

... PRODUCT SPECIFICATION FOR IMFORMATION ERJT06 Carrier tape Top tape Sprocket hole Chip hole Chip resistor 2.50+/-0.20 8.00+/-0. 2.00+/-0.05 4.00+/-0.10 1.50+0.10/-0 0.84+/-0.05 Panasonic Electronic Devices Co., Ltd. Spec. No. 151-SRJ-ET0601A 11 9.0 +/- 1.0 11.4 +/- 1.0 Unit : 3.50+/-0.05 1.75+/-0.10 ø ...

Page 11

... Poduction country PRODUCT SPECIFICATION FOR IMFORMATION ERJT06 Carrier tape Quantity : 20 reels (Max. 100,000pcs.) Panasonic Electronic Devices Co., Ltd. Spec. No. 151-SRJ-ET0601A - 11 Peeling direction 10 degree Top tape Tape ...

Page 12

... A A≤0 A≤W/4 A A≤W/4 W Protective coating and terminal aberration shall be within the terminal width dimension Marking must be readable. Panasonic Electronic Devices Co., Ltd. Spec. No. 151-SRJ-ET0601A 11 Remark criteria Chipping on both sides shall be considered defective chip resistor Pin hole penetrates The resistive material. ...