ENW-C9A25B1EF Panasonic - ECG, ENW-C9A25B1EF Datasheet - Page 8

• Manufacturer Part Number: ENW-C9A25B1EF
• Description: RF MODULE 802.15.4 UF.L NO SW
• Manufacturer: Panasonic - ECG
• Series: PAN4561r

Specifications of ENW-C9A25B1EF

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: General Purpose
• Power - Output: 10dBm
• Sensitivity: -102dBm
• Voltage - Supply: 2.7 V ~ 3.4 V
• Current - Receiving: 47mA
• Current - Transmitting: *
• Data Interface: PCB, Surface Mount
• Memory Size: 60kB Flash, 4kB RAM
• Antenna Connector: U.FL
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ENWC9A25B1EF

CLASSIFICATION
SUBJECT
CUSTOMER’S CODE
PAN4561H /M /L
PANASONIC ELECTRONIC DEVICES EUROPE GMBH
Note:
(1) PTG0 is output only. Pin is I/O when used as BDM function.
(2) Full I/O when not used as clock source. Please refer also to [2].
(3) CLKO (Pin 28) and PTG2/EXTAL (Pin 26) must be connected when the programmable clock derived
(4) PTG2 / EXTAL is not accessible with E-Senza software
Port PTA, PTB, PTC, PTD, PTE, PTG have internal software controlled pull-up resistors. For detailed
information refer to [3].
All I/O pins of port PTC are high current pins. The maximum current for all pins together must not exceed
60mA. A continuous current of 7mA, and 25mA burst for each port pin must not be exceeded. For detailed
information refer to [3].
Pin No.
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53 - 54
55
56 - 62
from the internal 16 MHz crystal.
Do not connect when the clock derived from Internal Reference Generator in MC13213.
Pin
PTG2 / EXTAL
RESET
CLKO
GPIO2
PTG0 / BKGND / MS
GPIO1
GND
VDDA
PTA7 / KBI1P7
PTA6 / KBI1P6
PTA5 / KBI1P5
PTA4 / KBI1P4
PTA3 / KBI1P3
PTA2 / KBI1P2
PTA1 / KBI1P1
PTA0 / KBI1P0
PTC7 / GPIO
PTC6 / GPIO
PTC5 / GPIO
PTC4 / GPIO
PTE0 / TXD1
PTE1 / RXD1
GPIO5
GPIO6
GPIO7
NC
NC
GND
EXANT
GND
MODEM FOR 802.15.4 IEEE STANDARD
PRODUCT SPECIFICATION
Pin Type
Dig. I/O / I
Dig. I
Dig. O
Dig. I/O
Dig. I/O
Dig. I/O
I/O
Power O
Dig. I/O
Dig. I/O
Dig. I/O
Dig. I/O
Dig. I/O
Dig. I/O
Dig. I/O
Dig. I/O
Dig. I/O
Dig. I/O
Dig. I/O
Dig. I/O
Dig. I/O
Dig. I/O
Dig. I/O
Dig. I/O
Dig. I/O
I/O
I/O
I/O
PANASONIC PART NUMBER
ENWC9A22xxEF / .25xx. / .21xx.
Description
MCU Port G Bit 2 / Crystal oscillator input
MCU reset. Active low
Programmable Clock Output (default: 32,768 kHz)
GPIO2 from RF transceiver unit
MCU Port G Bit 0 / Background / Mode Select
GPIO1 from RF transceiver unit
Ground
Modem analog regulated supply output - leave open
MCU Port A Bit 7 / Keyboard Input Bit 7
MCU Port A Bit 6 / Keyboard Input Bit 6
MCU Port A Bit 5 / Keyboard Input Bit 5
MCU Port A Bit 4 / Keyboard Input Bit 4
MCU Port A Bit 3 / Keyboard Input Bit 3
MCU Port A Bit 2 / Keyboard Input Bit 2
MCU Port A Bit 1 / Keyboard Input Bit 1
MCU Port A Bit 0 / Keyboard Input Bit 0
MCU Port C Bit 7 (GPIO)
MCU Port C Bit 6 (GPIO)
MCU Port C Bit 5 (GPIO)
MCU Port C Bit 4 (GPIO)
MCU Port E Bit 0 / SCI1 TX data out (UART1)
MCU Port E Bit 1/ SCI1 RX data in (UART1)
GPIO5 from RF transceiver unit
GPIO6 from RF transceiver unit
GPIO7 from RF transceiver unit
Not connected – leave open
Not connected – leave open
Ground
Pin for external antenna (50 Ω)
Ground
No.
DS-4561-2400-102
PAGE
DATE
www.pedeu.pansonic.de
(2) (3)
.
(1)
(4)
06.08.2010
(3)
8 of 34
REV.
G