CB-OBS433I-02-0 ConnectBlue, CB-OBS433I-02-0 Datasheet - Page 29
![no-image](/images/no-image-200.jpg)
CB-OBS433I-02-0
Manufacturer Part Number
CB-OBS433I-02-0
Description
SERIAL PORT ADAPTER BLUETOOTH
Manufacturer
ConnectBlue
Specifications of CB-OBS433I-02-0
Frequency
2.402GHz ~ 2.48GHz
Data Rate - Maximum
115 kbps
Modulation Or Protocol
Bluetoothv2.1+EDR
Applications
General Purpose
Power - Output
17dBm
Sensitivity
-94dBm
Voltage - Supply
3.3 V ~ 6 V
Current - Receiving
200mA
Current - Transmitting
200mA
Data Interface
Connector, 2 x 10 Header, 2 mm Pitch
Antenna Connector
On-Board, Chip
Operating Temperature
-40°C ~ 85°C
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
809-1038
connectBlue
Copyright © 2010 connectBlue AB
Read this information before using your OEM Serial Port Adapter.
For any exceptions, due to national requirements or limitations, when using your OEM Serial Port Adapter, please visit
www.bluetooth.org.
The OEM Serial Port Adapter contains a small radio transmitter and receiver. During communication with other Bluetooth products the
OEM Serial Port Adapter receives and transmits radio frequency (RF) electromagnetic fields (microwaves) in the frequency range 2400 to
2500 MHz. The output power of the radio transmitter is very low.
When using the OEM Serial Port Adapter, you will be exposed to some of the transmitted RF energy. This exposure is well below the
prescribed limits in all national and international RF safety standards and regulations.
Most modern electronic equipment, for example, in hospitals and cars, is shielded from RF energy. However, certain electronic
equipment is not. Therefore:
Turn off your electronic device before entering an area with potentially explosive atmosphere. It is rare, but your electronic device could
generate sparks. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death.
Areas with a potentially explosive atmosphere are often, but not always, clearly marked. They include fuelling areas, such as petrol
station, below deck on boats, fuel or chemical transfer or storage facilities, and areas where the air contains chemicals or particles, such
as grain, dust, or metal powders.
The OEM Serial Port Adapter must be supplied by a limited power source according to EN 60950-1.
9 Guidelines for Efficient and Safe Use
9.1 General
9.2 Product Care
9.3 Radio Frequency Exposure
9.4 Electronic Equipment
9.5 Potentially Explosive Atmospheres
9.6 Power Supply
Do not expose your product to liquid or moisture.
Do not expose you product to extreme hot or cold temperature (see section
Do not expose your product to lit candles, cigarettes, cigars, open flames, etc.
Do not drop, throw or try to bend your product since rough treatment could damage your product.
Do not attempt to disassemble your product. Doing so will void warranty. The product does not contain consumer serviceable or
replaceable components. Service should only be performed by connectBlue AB.
Do not paint your product as the paint could prevent normal use.
If you will not be using your product for a while, store it in a place that is dry, free from damp, dust and extreme heat and cold.
The clearance and creepage distances required by the end product must be withheld when the module is installed.
The cooling of the end product shall not negatively be influenced by the installation of the module when the module is installed.
Connect your power supply only to designated power-sources as marked on the product.
Make sure all cords and cable are positioned so that they will not be stepped on, tripped over or otherwise subject to damage or
stress.
To reduce risk of electric shock, unplug the unit from any power source before attempting to clean it.
NOTE
Changes or modifications to the product not expressly approved by connectBlue AB will void the user's authority to
operate the equipment.
NOTE
This equipment emits RF energy in the ISM (Industrial, Scientific, Medical) band. Please insure that all medical devices
used in proximity to this device meet appropriate susceptibility specifications for this type of RF energy.
Environmental
for further information).
Page 29 of 42