HSDL-3020-021 Avago Technologies US Inc., HSDL-3020-021 Datasheet
![Infrared Transceivers Orion 2 FIR + RC](/photos/26/70/267015/hsdl-3020_wht_sml.jpg)
HSDL-3020-021
Specifications of HSDL-3020-021
Related parts for HSDL-3020-021
HSDL-3020-021 Summary of contents
Page 1
... Data Compliant Low Power 4.0 Mbit/s with Remote Control Infrared Transceiver Data Sheet Description The HSDL-3020 is a new generation low profile high speed enhanced infrared (IR) transceiver module that provides the capability of (1) interface between logic and IR signals for through-air, serial, half-duplex IR ...
Page 2
... Rx PULSE 9 SHAPER LED DRIVER LED DRIVER 1 1 Order Information Part Number Packaging Type HSDL-3020-021 Tape and Reel Marking Information The unit is marked with “7YWLL” on the shield Y = Year W = Work week LL = Lot information Package Quantity Front Option 2500 ...
Page 3
I/O Pins Configuration Table Pin Symbol Description 1 RC_LEDC RC LED Cathode 2 RC_LEDA RC LED Anode 3 IR_LEDA IR LED Anode 4 IOV Input/Output ASIC Voltage CC 5 TxD_IR IrDA Transmitter Data Input 6 RxD IrDA Receive Data 7 ...
Page 4
... CX1, CX3, CX5, CX6 100 nF, 20%, X7R Ceramic CX2, CX4, CX7 4.7 F, 20%, Tantalum Note: 1. CX1, CX2, CX3, CX4, CX5, CX6 & CX7 must be placed within 0 HSDL-3020 to obtain optimum noise immunity. Absolute Maximum Ratings For implementations where case to ambient thermal resistance is 50 C/W. Parameter ...
Page 5
Recommended Operating Conditions Parameter Operating Temperature Supply Voltage Input/Output Voltage Logic Input Voltage Logic High for TXD, SD/Mode Logic Low Receiver Input Logic High Irradiance Logic Low LED (Logic High) Current Pulse Amplitude – SIR Mode LED (Logic High) Current ...
Page 6
Electrical and Optical Specifications Specifications (Min. & Max. values) hold over the recommended operating conditions unless otherwise noted. Unspecified test conditions may be anywhere in their operating range. All typical values (Typ.) are with V 3.0 V ...
Page 7
Electrical and Optical Specifications (Cont’d.) Parameter IR LED Anode On-State Voltage (SIR Mode) IR LED Anode On-State Voltage (MIR/FIR Mode) Remote Control (RC) Transmitter RC Radiant Intensity RC Viewing Angle RC Peak Wavelength TxD_RC Logic Levels High Low TxD_RC Input ...
Page 8
IR SIR Mode - VLED_A vs ILED 2.3 2.2 2.1 2.0 1.9 1.8 1.7 1.6 1.5 1.4 0 0.02 0.04 0.06 ILED (A) IR SIR Mode - Radiant Intensity vs ILED ...
Page 9
... HSDL-3020 Package Dimensions 2.50 1.20 R1.10 0.95 1.80 COPLANARITY 0.68 0. MOUNTING 5.20 CENTER 10.40 R2.10 3.60 5. RECEIVER EMITTER EMITTER R1.10 R1. PITCH 0.95 0.60 1.025 1. RC CATHODE 2. RC VLED 3. IR VLED 4. IOV CC 1.15 5. TxD IR 6. RxD 7. SD 1.20 8. VDD 9. TxD RC 10 ...
Page 10
... HSDL-3020 Tape and Reel Dimensions SECTION A-A SYMBOL A 0 SPEC. 2.95 0.10 SYMBOL E SPEC. 1.75 0.10 NOTES SPROCKET HOLE PITCH CUMULATIVE TOLERANCE IS 0.2 mm. 2. CARRIER CHAMBER SHALL BE NOT MORE THAN 1 mm PER 100 mm THROUGH A LENGTH OF 250 mm AND B 0 MEASURED ON A PLACE 0.3 mm ABOVE THE BOTTOM OF THE POCKET. ...
Page 11
... HSDL-3020 Moisture Proof Packaging All HSDL-3020 options are shipped in moisture proof package. Once opened, moisture absorption begins. This part is compliant to JEDEC Level 4. YES NO BAKING IS NECESSARY PERFORM RECOMMENDED Figure 3. Baking conditions chart. 11 UNITS IN A SEALED MOISTURE-PROOF PACKAGE PACKAGE IS OPENED (UNSEALED) ENVIRONMENT LESS THAN 30 C, ...
Page 12
... The cool down rate, R5, from the liquidus point of the solder (77 F) should not exceed 6 C per second maximum. This limitation is necessary to allow the PC board and HSDL-3020 castellations to change dimensions evenly, putting minimal stresses on the HSDL- 3020 transceiver. ...
Page 13
... Appendix A: HSDL3020 SMT Assembly Application Note Solder Pad, Mask and Metal Stencil STENCIL APERTURE SOLDER MASK Figure 1. Stencil and PCBA. Recommended Land Pattern 0.35 1.75 Figuure 2. 13 METAL STENCIL FOR SOLDER PASTE PRINTING LAND PATTERN PCBA MOUNTING CENTER 2.7 1.25 2.05 ...
Page 14
Recommended Metal solder Stencil Aperture It is recommended that only a 0.152 mm (0.006 inch 0.127 mm (0.005 inch) thick stencil be used for solder paste printing. This is to ensure adequate printed solder paste volume and no ...
Page 15
Appendix B: PCB Layout Suggestion The effects of EMI and power supply noise can potentially reduce the sensitivity of the receiver, resulting in reduced link distance. The PCB layout played an important role to obtain a good PSRR and EM ...
Page 16
NOISE SOURCES TO BE PLACED AS FAR AWAY FROM THE TRANSCEIVER AS POSSIBLE CX6 CX7 LAYER BOTTOM LAYER (GND) The area underneath the module at the second layer, and all directions around the module, ...
Page 17
... Appendix C: General Application Guide for the HSDL-3020 Infrared IrDA Compliant 4 Mb/s Transceiver Description The HSDL-3020, a wide-voltage operating range infrared transceiver is a low-cost and small form factor device that is designed to address the mobile computing market such as PDAs, as well as small embedded mobile products such as digital cameras and cellular phones ...
Page 18
... CX6 GND IR_RxD GPIO IR_TxD 100 kW GND Figure 3: HSDL-3020 configuration with general mobile architecture processor. Remote Control Operation The HSDL-3020 is spectrally suited to universal remote control transmission function at 940 nm typically. Remote control applications are not governed by any standards, owing to which there are numerous remote codes in market ...
Page 19
... In the figure above the width of the window the height of window the distance from the HSDL-3020 to the back of the window, and T is the thickness of the IR transparent window. 19 OPAQUE MATERIAL IR TRANSPARENT WINDOW Z Module Depth, Min ...
Page 20
APERTURE WIDTH (X) vs. MODULE DEPTH APERTURE DEPTH (Z) – mm For the modules depth values that are not shown on the tables above, the ...
Page 21
Shape of the Window From an optics standpoint, the window should be flat. This ensures that the window will not alter either the radiation pattern of the LED, or the receive pattern of the photodiode. If the window must be ...
Page 22
... Appendix E: General Application Guide for the HSDL-3020 Remote Control Drive Modes The HSDL-3020 can operate in the single-TxD programmable mode or the two-TxD direct transmission mode. Single-TxD Programmable Mode In the single-TxD programmable mode, only one input pin (TxD_IR input pin) is used to turn on the ...
Page 23
Two-TxD Direct Transmission Mode In the two-TxD direct transmission mode, the IrDA (875 nm) LED and the remote control (940 nm) LED are turned on separately by two different input pins. The TxIR input pin is Transceiver Control I/O Truth ...
Page 24
For product information and a complete list of distributors, please go to our website: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright © ...