PVZ3A503A01R00 Murata, PVZ3A503A01R00 Datasheet - Page 32
![Trimmer Resistors - SMD 50K OHM SMD 3MM](/photos/16/51/165154/130p01_sml.jpg)
PVZ3A503A01R00
Manufacturer Part Number
PVZ3A503A01R00
Description
Trimmer Resistors - SMD 50K OHM SMD 3MM
Manufacturer
Murata
Type
Trimmerr
Series
PVZ3Ar
Datasheet
1.PVZ3A503A01R00.pdf
(59 pages)
Specifications of PVZ3A503A01R00
Resistance
50kohm
Power Rating
1/10W
Tolerance (+ Or -)
30%
Number Of Turns
1Turn
Technology
Carbon Film
Mounting Style
Surface Mount
Termination Style
J-Hook
Operating Temp Range
-25C to 85C
Failure Rate
Not Required
Shaft Diameter (mm)
3mm
Product Diameter (mm)
Not Requiredmm
Product Length (mm)
3.1mm
Product Height (mm)
1.85mm
Product Depth (mm)
3.6mm
Temperature Coefficient
±500
Tolerance
30 %
Operating Temperature Range
- 25 C to + 85 C
Element Type
Carbon
Product
Single-Turn Trimmer Potentiometers
Taper
Linear
Lead Free Status / RoHS Status
Compliant
6
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Store in temperatures of -10 to +40 deg. C and
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. If you use the trimmer potentiometer in an
1. When using with partial load (rheostat), minimize
2. The maximum input voltage to a trimmer
1. Soldering
30
PVG5 Series Notice
(1) Soldering condition
(2) Cannot be soldered using the flow soldering
(3) The soldering iron should not come in contact
(4) Insufficient amounts of solder can lead to
Notice (Operating and Storage Conditions)
relative humidity of 30-85%.
environment other than listed below, please
consult with a Murata factory representative prior
to using.
The trimmer potentiometer should not be used under
the following environmental conditions:
Notice (Rating)
the power depending on the resistance value.
potentiometer should not exceed (P•R)^1/2 or the
maximum operating voltage, whichever is smaller.
Notice (Soldering and Mounting)
Refer to the temperature profile.
If the soldering conditions are not suitable,
e.g., excessive time and/or excessive
temperature, the trimmer capacitor may deviate
from the specified characteristics.
method. If you use the flow soldering method,
the trimmer potentiometer may not function.
with the case of the trimmer potentiometer. If
such contact does occur, the trimmer
potentiometer may be damaged.
insufficient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2. Mounting
3. Cleaning
(1) Corrosive gaseous atmosphere
(2) In liquid
(3) Dusty/dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
(1) Use our standard land dimension. Excessive land
(2) Do not apply excessive force, preferably 9.8N
(3) Do not warp and/or bend PC board to prevent
(4) In chip placers, the recommended size of the
Isopropyl-alcohol and Ethyl-alcohol are applicable
solvents for cleaning. If you use any other types of
solvents, please consult with a Murata factory
representative prior to using.
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(Ex. Oil, Medical liquid, Organic solvent, etc.)
area causes displacement due to the effect of
the surface tension of the solder. Insufficient
land area leads to insufficient soldering strength
of the chip.
max. (Ref. 1kgf) when the trimmer potentiometer
is mounted to the PCB.
trimmer potentiometer from breakage.
cylindrical pick-up nozzle should be outer
dimension 4.0mm dia. and inner dimension 2.0mm
dia.
R50E.pdf
08.8.26