PVZ3A503A01R00 Murata, PVZ3A503A01R00 Datasheet - Page 53
![Trimmer Resistors - SMD 50K OHM SMD 3MM](/photos/16/51/165154/130p01_sml.jpg)
PVZ3A503A01R00
Manufacturer Part Number
PVZ3A503A01R00
Description
Trimmer Resistors - SMD 50K OHM SMD 3MM
Manufacturer
Murata
Type
Trimmerr
Series
PVZ3Ar
Datasheet
1.PVZ3A503A01R00.pdf
(59 pages)
Specifications of PVZ3A503A01R00
Resistance
50kohm
Power Rating
1/10W
Tolerance (+ Or -)
30%
Number Of Turns
1Turn
Technology
Carbon Film
Mounting Style
Surface Mount
Termination Style
J-Hook
Operating Temp Range
-25C to 85C
Failure Rate
Not Required
Shaft Diameter (mm)
3mm
Product Diameter (mm)
Not Requiredmm
Product Length (mm)
3.1mm
Product Height (mm)
1.85mm
Product Depth (mm)
3.6mm
Temperature Coefficient
±500
Tolerance
30 %
Operating Temperature Range
- 25 C to + 85 C
Element Type
Carbon
Product
Single-Turn Trimmer Potentiometers
Taper
Linear
Lead Free Status / RoHS Status
Compliant
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
No.
13
14
Specifications and Test Methods
SMD Sealed Type (PVF2/G3/M4A_D01/G5)/Lead Sealed Type (PV32/12/37/36) Specifications and Test Methods
Continued from the preceding page.
Low Temperature Operation
(Only for PVF2 and
PVM4A---D01)
Rotational Life
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
The trimmer potentiometer should be placed in a chamber at a temperature of -25±3°C (-55±3°C for PVM4A---
D01 series) 48±4 hours without loading. The trimmer potentiometer should be removed from the chamber, and main-
tained at a temperature of 25±5°C for 1-2 hours.
1)PV-- series
Full rated continuous working voltage not exceeding the maximum rated voltage should be applied with the circuit
shown in the figure. The adjustment rotor (screw) should be continuously cycled through not less than 90% of effec-
tive-electrical rotational angle (number of turns), at the rate of 1 cycle for 5 seconds minimum to 2.5 minutes maxi-
mum for total of 200 cycles.
2) PVG3, PVG5 series
The adjustment rotor (screw) should be continuously cycled though not less than 90% of effective-electrical rotation-
al angle (number of turns), at the rate of 1 cycle for 5 seconds minimum to 2.5 minutes maximum for a total of 50
(100 for PVG5) cycles, without loading.
3) PVF2, PVM4A---D01 series
The wiper should be rotated over 90% of the effective rotational angle without loading at a speed of 10 cycles per
minute, for 100 cycles continuously.
End Terminal
Resistor 1
End Terminal
Figure 4
DC supply
End Terminal
Resistor 2 End Terminal
Test Methods
R50E.pdf
51
08.8.26
8