NCP1608BDR2G ON Semiconductor, NCP1608BDR2G Datasheet - Page 10

• Manufacturer Part Number: NCP1608BDR2G
• Description: IC PFC CTLR/PRECONVERTER 8-SOIC
• Manufacturer: ON Semiconductor

Specifications of NCP1608BDR2G

• Mode: Critical Conduction (CRM)
• Frequency - Switching: Adjustable
• Current - Startup: 24µA
• Voltage - Supply: 8.8 V ~ 12.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Switching Frequency: 70 KHz
• Maximum Power Dissipation: 450 mW
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Introduction
(PFC) controller designed to drive cost−effective
pre-converters to comply with line current harmonic
regulations. This controller operates in critical conduction
mode (CrM) suitable for applications up to 350 W. Its
voltage mode scheme enables it to obtain near unity power
factor without the need for a line-sensing network. A high
precision transconductance error amplifier regulates the
output voltage. The controller implements comprehensive
safety features for robust designs.
The key features of the NCP1608 are:
•
•
•
•
•
•
•
•
•
The NCP1608 is a voltage mode, power factor correction
Constant On Time (Voltage Mode) CrM Operation. A
high power factor is achieved without the need for
input voltage sensing. This enables low standby power
consumption.
Accurate and Programmable On Time Limitation. The
NCP1608 uses an accurate current source and an
external capacitor to generate the on time.
Wide Control Range. In high power applications (>
150 W), inadvertent skipping can occur at high input
voltage and high output power if noise immunity is
not provided. The noise immunity provided by the
NCP1608 prevents inadvertent skipping.
High Precision Voltage Reference. The error amplifier
reference voltage is guaranteed at 2.5 V ±1.6% over
process and temperature. This results in accurate
output voltages.
Low Startup Current Consumption. The current
consumption is reduced to a minimum (< 35 mA)
during startup, enabling fast, low loss charging of
V
provides sufficient V
reduce the value of the V
Powerful Output Driver. A Source 500 mA / Sink
800 mA totem pole gate driver enables rapid turn on
and turn off times. This enables improved efficiencies
and the ability to drive higher power MOSFETs. A
combination of active and passive circuits ensures that
the driver output voltage does not float high if V
does not exceed V
Accurate Fixed Overvoltage Protection (OVP). The
OVP feature protects the PFC stage against excessive
output overshoots that may damage the system.
Overshoots typically occur during startup or transient
loads.
Undervoltage Protection (UVP). The UVP feature
protects the system if there is a disconnection in the
power path to C
Protection Against Open Feedback Loop. The OVP
and UVP features protect against the disconnection of
the output divider network to the FB pin. An internal
resistor (R
floating (Floating Pin Protection, FPP).
CC
. The NCP1608 includes undervoltage lockout and
FB
) protects the system when the FB pin is
bulk
CC(on)
(i.e. C
CC
hysteresis during startup to
.
CC
bulk
capacitor.
is unable to charge).
http://onsemi.com
CC
10
•
•
Application Information
use a diode bridge rectifier and a bulk storage capacitor to
produce a dc voltage from the utility ac line (Figure 24).
This DC voltage is then processed by additional circuitry
to drive the desired output.
when the instantaneous ac voltage exceeds the capacitor
voltage. This occurs near the line voltage peak and the
resulting current is non-sinusoidal with a large harmonic
content. This results in a reduced power factor (typically <
0.6). Consequently, the apparent input power is higher than
the real power delivered to the load. If multiple devices are
connected to the same input line, the effect increases and
a “line sag” is produced (Figure 25).
line current harmonic content. Power factor correction is
implemented with either a passive or an active circuit to
comply with regulations. Passive circuits contain a
combination of large capacitors, inductors, and rectifiers
that operate at the ac line frequency. Active circuits use a
AC Line Current
Most electronic ballasts and switching power supplies
This rectifying circuit consumes current from the line
Government regulations and utilities require reduced
Overcurrent Protection (OCP). The inductor peak
current is accurately limited on a cycle-by-cycle basis.
The maximum inductor peak current is adjustable by
modifying the current sense resistor. An integrated
LEB filter reduces the probability of noise
inadvertently triggering the overcurrent limit.
Shutdown Feature. The PFC pre-converter is shutdown
by forcing the FB pin voltage to less than V
shutdown mode, the I
reduced and the error amplifier is disabled.
AC Line Voltage
Figure 25. Typical Line Waveforms without PFC
Line
Rectified DC
AC
Figure 24. Typical Circuit without PFC
V
peak
0
0
Rectifiers
CC
+
Line
Sag
Capacitor
current consumption is
Bulk
Storage
Converter
UVP
. In
Load