AVR-TLCD-128CAN Olimex Ltd., AVR-TLCD-128CAN Datasheet

Page 1

... AVR-TLCD-128CAN development board Copyright(c) 2008, OLIMEX Ltd, All rights reserved Users Manual Rev.A, July 2008 ...

Page 2

... INTRODUCTION: AVR-TLCD-128CAN adds cool LCD and touchscreen interface to your next project. There is AT90CAN128 on board with all microcontroller pins available for plug-in additional boards BOARD FEATURES: MCU: AT90CAN128 128KB Flash memory, 4096B RAM, 4096B EEPROM TOUCH SCREEN LCD 160x160 dots B/W 81x60 mm view area Stainless steel front panel (102x85 mm 4x3 ...

Page 3

... AVR Studio 4.13 (or later) + WinAVR (latest version) or IAR AVR. AVR Studio and WinAVR are free to download and use. Take a note that AVR Studio 4.13 has a bug and doesn't read the fuses correctly. On our request to Atmel support they had confirmed the bug and had suggested to fix the bug by “AVR Studio 4 ...

Page 4

... PROCESSOR FEATURES: AVR-TLCD-128CAN board use MCU AT90CAN128 from Atmel with these features: High-performance, Low-power AVR® 8-bit Microcontroller Advanced RISC Architecture - 133 Powerful Instructions – Most Single Clock Cycle Execution - General Purpose Working Registers + Peripheral Control Registers - Fully Static Operation - MIPS Throughput at 16 MHz ...

Page 5

Differential Channels With Programmable Gain at 1x, o 10x, or 200x - On-chip Analog Comparator - Byte-oriented Two-wire Serial Interface - Dual Programmable Serial USART - Master/Slave SPI Serial Interface Programming Flash (Hardware ISP) o Special Microcontroller Features - ...

Page 6

BLOCK DIAGRAM: ...

Page 7

MEMORY MAP: SCHEMATIC: ...

Page 8

...

Page 9

... AVR-TLCD-128CAN should be powered by 4.5VAC or +(6-9VDC). The board power consumption at 8 VDC the consumption is about 20 mA. RESET CIRCUIT: AVR-TLCD-128CAN reset circuit is realized with MCP130T which on power failure or if you apply low level at EXT-3 resets the MCU. CLOCK CIRCUIT: Quartz crystal 8 MHz is connected to AT90CAN128 pin 24 (XTAL1) and pin 23 (XTAL2) ...

Page 10

JUMPER DESCRIPTION: 18V_E . devices Default state is closed. CAN_T the bus it with CAN, the jumpers of both devices should be closed. If you have more than two devices, only the two end-devices should be closed. Default state is ...

Page 11

INPUT/OUTPUT: Power-on red LED with name PWR_LED connected to EXT-1 and EXT-2. Accelerometer SMB380. Touchscreen LCD PC0919WE07. ...

Page 12

EXTERNAL CONNECTORS DESCRIPTION: ICSP: Pin # 1 PDI 2 +3. GND 5 RESET 6 GND 7 SCK 8 GND 9 PDO 10 GND PDI Input Programming Data In. This pin is used for data input while programming ...

Page 13

JTAG: Pin # 1 TCK 2 GND 3 TDO 4 +3.3V 5 TMS 6 RESET 7 +3. TDI 10 GND TCK Input Test Clock. This allows shifting of the data in, on the TMS and TDI pins. ...

Page 14

UEXT: Pin # 1 +3.3V 2 GND 3 TXD 4 RXD 5 SCL 6 SDA 7 MISO 8 MOSI 9 SCK 10 SS TXD Output Transmit Data. This is the output data line for the UART. RXD Input Receive Data. ...

Page 15

CAN: Pin # 1 GND 2 CANL 3 CANH CANL and CANH are either deferential input, or differential output depending on the function of the SN65FVD230 CAN controller (receiving or transmitting data). SD/MMC card slot: Pin # 1 CS_SD 3 ...

Page 16

MISO Master In Slave Out. As the access to the memory card is via SPI I/O interface, this is data input for the MCU(which is master) and data output from the memory card (which is slave). WP_E Write Protect Enable. ...

Page 17

... MECHANICAL DIMENSIONS: All measures are in mm AVAILABLE DEMO SOFTWARE : You could find information about AVR-TLCD-128CAN demo software at www.olimex.com/dev . ...

Page 18

... ORDER CODE: AVR-TLCD-128CAN – assembled and tested (no kit, no soldering required) How to order? You can order to us directly or by any of our distributors. Check our web All boards produced by Olimex are RoHS compliant Revision history: REV.A www.olimex.com/dev - created July 2008 for more info. ...

Page 19

... OLIMEX in good faith. However all warranties implied or expressed including but not limited to implied warranties of merchantability or fitness for purpose are excluded. This document is intended only to assist the reader in the use of the product. OLIMEX Ltd. shall not be liable for any loss or damage arising from the use of any information in this ...