AD5292BRUZ-100 Analog Devices Inc, AD5292BRUZ-100 Datasheet - Page 11

• Manufacturer Part Number: AD5292BRUZ-100
• Description: 1024 Tap, 1% DigiPOT With SPI Interface
• Manufacturer: Analog Devices Inc

Specifications of AD5292BRUZ-100

• Design Resources: Variable Gain Noninverting Amplifier Using AD5292 and OP184 (CN0112) Variable Gain Inverting Amplifier Using AD5292 and OP184 (CN0113) Low Cost, High Voltage, Programmable Gain Instrumentation Amplifier Using AD5292 and AD8221 (CN0114) Programmable High Voltage Source with Boosted Output Current Using AD5292, OP184, and MOSFETs (CN0115) Programmable Bidirectional Current Source Using AD5292 and ADA4091-4 (CN0117) Logarithmic Audio Volume Control with Glitch Reduction Using AD5292 (CN0120)
• Taps: 1024
• Resistance (ohms): 100K
• Number Of Circuits: 1
• Temperature Coefficient: 35 ppm/°C Typical
• Memory Type: Non-Volatile
• Interface: SPI Serial
• Voltage - Supply: 9 V ~ 33 V, ±9 V ~ 16.5 V
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 14-TSSOP
• Resistance In Ohms: 100K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Table 10. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Mnemonic
RESET
V
A
W
B
V
EXT_CAP
V
GND
DIN
SCLK
SYNC
SDO
RDY
SS
DD
LOGIC
Description
Hardware Reset Pin. Refreshes the RDAC register with the contents of the 20-TP memory register. Factory
default loads midscale until the first 20-TP wiper memory location is programmed. RESET is activated at the
logic high transition. Tie RESET to V
Negative Supply. Connect to 0 V for single-supply applications. This pin should be decoupled with 0.1 μF
ceramic capacitors and 10 μF capacitors.
Terminal A of RDAC. V
Wiper Terminal of RDAC. V
Terminal B of RDAC. V
Positive Power Supply. This pin should be decoupled with 0.1 μF ceramic capacitors and 10 μF capacitors.
External Capacitor. Connect a 1 μF capacitor to EXT_CAP. This capacitor must have a voltage rating of ≥7 V.
Logic Power Supply; 2.7 V to 5.5 V. This pin should be decoupled with 0.1 μF ceramic capacitors and 10 μF
capacitors.
Ground Pin, Logic Ground Reference.
Serial Data Input. The AD5291 and AD5292 have a 16-bit shift register. Data is clocked into the register on the
falling edge of the serial clock input.
Serial Clock Input. Data is clocked into the shift register on the falling edge of the serial clock input. Data can be
transferred at rates up to 50 MHz.
Falling Edge Synchronization Signal. This is the frame synchronization signal for the input data. When SYNC
goes low, it enables the shift register and data is transferred in on the falling edges of the following clocks. The
selected register is updated on the rising edge of SYNC following the 16
before the 16
the DAC.
Serial Data Output. This open-drain output requires an external pull-up resistor. SDO can be used to clock data
from the shift register in daisy-chain mode or in readback mode.
Ready Pin. This active-high open-drain output identifies the completion of a write or read operation to or from
the RDAC register or memory.
th
clock cycle, the rising edge of SYNC acts as an interrupt, and the write sequence is ignored by
SS
SS
≤ V
≤ V
EXT_CAP
SS
B
A
RESET
≤ V
≤ V
≤ V
V
V
Figure 5. Pin Configuration
DD
SS
W
W
DD
DD
A
B
≤ V
Rev. D | Page 11 of 32
.
.
1
2
3
4
5
6
7
LOGIC
DD
Not to Scale
AD5291/
TOP VIEW
AD5292
.
if not used.
14
13
12
11
10
9
8
RDY
SDO
SCLK
DIN
GND
SYNC
V
LOGIC
th
clock cycle. If SYNC is taken high
AD5291/AD5292