AD7352BRUZ-500RL7 Analog Devices Inc, AD7352BRUZ-500RL7 Datasheet - Page 13

• Manufacturer Part Number: AD7352BRUZ-500RL7
• Description: 12-Bit Dual Diff Simult 3 MSPS ADC I.C.
• Manufacturer: Analog Devices Inc

Specifications of AD7352BRUZ-500RL7

• Design Resources: DC-Coupled, Single-Ended-to-Differential Conversion Using AD8138 and AD7352 (CN0040)
• Number Of Bits: 12
• Sampling Rate (per Second): 3M
• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Number Of Converters: 2
• Power Dissipation (max): 45mW
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-TSSOP (0.173", 4.40mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

For ac applications, removing high frequency components from
the analog input signal is recommended by the use of an RC
low-pass filter on the analog input pins. In applications where
harmonic distortion and signal-to-noise ratio are critical, the
analog input should be driven from a low impedance source.
Large source impedances significantly affect the ac perfor-
mance of the ADC and may necessitate the use of an input
buffer amplifier. The choice of the op amp is a function of the
particular application.
When no amplifier is used to drive the analog input, limit
the source impedance to low values. The maximum source
impedance depends on the amount of THD that can be
tolerated. THD increases as the source impedance increases
and performance degrades. Figure 17 shows a graph of THD
vs. the analog input signal frequency for different source
impedances.
Figure 18 shows a graph of the THD vs. the analog input
frequency while sampling at 3 MSPS. In this case, the source
impedance is 33 Ω.
Figure 17. THD vs. Analog Input Signal Frequency for Various Source
–65
–67
–69
–71
–73
–75
–77
–79
–81
–83
–85
–87
–89
–66
–70
–74
–78
–82
–86
–90
100
0
1000 2000 3000 4000 5000 6000 7000 8000 9000 10000
Figure 18. THD vs. Analog Input Frequency
500
ANALOG INPUT FREQUENCY (kHz)
100Ω
Impedances
FREQUENCY (kHz)
1000
50Ω
1500
33Ω
10Ω
2000
2500
Rev. 0 | Page 13 of 20
ANALOG INPUTS
Differential signals have some benefits over single-ended
signals, including noise immunity based on the devices
common-mode rejection and improvements in distortion
performance. Figure 19 defines the fully differential input of
the AD7352.
The amplitude of the differential signal is the difference
between the signals applied to the V
each differential pair (V
simultaneously driven by two signals each of amplitude (V
that are 180° out of phase. This amplitude of the differential
signal is, therefore −V
the common mode (CM).
CM is the average of the two signals and is, therefore, the
voltage on which the two inputs are centered.
This results in the span of each input being CM ± V
voltage has to be set up externally. When setting up the CM,
ensure that V
a conversion takes place, CM is rejected, resulting in a virtually
noise-free signal of amplitude, −V
to the digital codes of 0 to 4095 for the AD7352.
CM = (V
COMMON-MODE
VOLTAGE
*
IN+
ADDITIONAL PINS OMITTED FOR CLARITY.
IN+
Figure 19. Differential Input Definition
and V
+ V
IN−
REF
IN−
)/2
IN+
to +V
remain within GND/V
− V
V
V
REF
REF
IN−
REF
). V
p-p
p-p
peak-to-peak regardless of
REF
IN+
IN+
to +V
and V
and V
V
V
REF
AD7352*
IN+
IN–
IN−
, corresponding
IN−
pins in
DD
should be
. When
REF
AD7352
/2. This
REF
)