AD7398BR Analog Devices Inc, AD7398BR Datasheet - Page 15
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD7398BR
Manufacturer Part Number
AD7398BR
Description
D/A Converter (D-A) IC
Manufacturer
Analog Devices Inc
Datasheet
1.AD7399BRUZ.pdf
(24 pages)
Specifications of AD7398BR
Resolution (bits)
12bit
Digital Ic Case Style
SOIC
No. Of Pins
16
Operating Temperature Range
-40°C To +125°C
Update Rate
0.167MSPS
Mounting Type
Surface Mount
Peak Reflow Compatible (260 C)
No
Rohs Status
RoHS non-compliant
Settling Time
6µs
Number Of Bits
12
Data Interface
Serial
Number Of Converters
4
Voltage Supply Source
Dual ±
Power Dissipation (max)
16mW
Operating Temperature
-40°C ~ 125°C
Package / Case
16-SOIC (0.300", 7.5mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD7398BR
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD7398BRUZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD7398BRZ
Manufacturer:
Analog Devices Inc
Quantity:
135
Part Number:
AD7398BRZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
OPERATION WITH V
The AD7398/AD7399 are designed to approach the full output
voltage swing from ground to V
swing is achieved when the corresponding V
to the same power supply. This power supply should be low noise
and low ripple, preferably operated by a suitable reference voltage
source such as ADR292 or REF02. The output swing is limited
by the internal buffer offset voltage and the output drive current
capability of the output stage. Users should at least budget the V
offset voltage as the closest the output voltage can get to either
supply voltage under a no load condition. Under a loaded output,
degrade the headroom by a factor of 2 mV per 1 mA of load
current. Also note that the internal op amp has an offset voltage
so that the first eight codes of AD7398 may not respond at the
supply voltage or at ground until the internal DAC voltage
exceeds the offset voltage of the output buffers. Similarly, the first
two codes of AD7399 should not be used.
POWER SUPPLY SEQUENCING
V
analog supplies. The external reference input can be supplied from
the same supply to avoid a possible latch-up when the reference is
powered on prior to V
V
the power-up sequence is GND, V
output. The reverse sequence applies to the power-down sequence.
The order of V
In addition, V
GND or some other power sources to ensure a similar power-
up/power-down sequence.
PROGRAMMABLE POWER SHUTDOWN
The two MSBs of the serial input register, SA and SD, are used
to program various shutdown modes. If SA is set to Logic 1, all
DACs are placed in shutdown mode. If SA = 0 and SD = 1, a
corresponding DAC is shutdown addressed by Bit A0 and
Bit A1 (see the Input Registers section).
WORST CASE ACCURACY
Assuming a perfect reference, the worst-case output voltage can
be calculated from the following equation:
where:
D = decimal code loaded to DAC ranges 0 ≤ D ≤ 2
N = number of bits.
V
V
V
INL = integral nonlinearity in volts. INL is 0 at full scale or zero
scale.
REF
FSE
ZSE
DD
DD
/V
/V
= full-scale error in volts.
= zero-scale error in volts.
= applied reference voltage.
V
SS
SS
OUT
. If V
of AD7398/AD7399 should be powered from the system
DD
2
D
REF
N
REF
/V
pins of the unused DACs should be connected to
SS
and digital input/digital output is not important.
V
and V
REF
DD
/V
REF
V
REF
SS
FSE
, or powered off subsequent to
have separate power sources, ensure
EQUAL TO THE SUPPLY
DD
V
DD
ZSE
or V
, V
SS
, V
INL
SS
. The maximum output
REF
/digital input/digital
REF
input pin is tied
N
–1.
Rev. C | Page 15 of 24
ZSE
(3)
SERIAL DATA INTERFACE
The AD7398/AD7399 uses a 3-wire ( CS , SDI, CLK) SPI-
compatible serial data interface. Serial data of the AD7398 and
AD7399 is clocked into the serial input register in a 16-bit and 14-
bit data-word format, respectively. MSBs are loaded first. The Input
Registers section defines the 16 data-word bits for AD7398 and the
14 data-word bits for the AD7399. Data is placed on the SDI pin,
and clocked into the register on the positive clock edge of CLK,
subject to the data setup and data hold time requirements specified
in the Specifications section. Data can only be clocked in while the
CS chip select pin is active low. For the AD7398, only the last 16
bits clocked into the serial register are interrogated when the CS pin
returns to the logic high state, and extra data bits are ignored. For
the AD7399, only the last 14 bits clocked into the serial register are
interrogated when the CS pin returns to the logic high state.
Because most microcontrollers output serial data is in eight-bit
bytes, two right-justified data bytes can be written to the AD7398
and AD7399. Keeping the CS line low between the first and second
byte transfers results in a successful serial register update.
Once the data is properly aligned in the shift register, the positive
edge of the CS initiates the transfer of new data to the target DAC
register, determined by the decoding of Address Bit A1 and
Address Bit A0. For the AD7398, Table 5, Table 6, the Input
Registers section, Figure 3, and Figure 4 define the characteristics
of the serial interface. For the AD7399, Table 5, Table 6, the Input
Registers section, and Figure 4 (with a 14-bit exception) define the
characteristics of the serial interface. Figure 27 and Figure 28 show
the equivalent logic interface for the key digital control pins for
AD7398 and AD7399.
An asynchronous RS provides hardware control reset to zero-
code state over the preset function and DAC register loading. If
this function is not needed, the RS pin can be tied to logic high.
CLK
SDI
CS
Figure 27. Equivalent Logic Interface
EN
TO INPUT REGISTER
AD7398/AD7399
REGISTER
DECODER
ADDRESS
SHIFT
A
B
C
D