AD7898AR-10 Analog Devices Inc, AD7898AR-10 Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD7898AR-10
Manufacturer Part Number
AD7898AR-10
Description
A/D Converter (A-D) IC
Manufacturer
Analog Devices Inc
Datasheet
1.AD7898ARZ-10REEL.pdf
(16 pages)
Specifications of AD7898AR-10
No. Of Bits
12 Bit
Mounting Type
Surface Mount
No. Of Channels
1
Interface Type
Serial
Package / Case
8-SOIC
Rohs Status
RoHS non-compliant
Number Of Bits
12
Sampling Rate (per Second)
220k
Data Interface
Serial
Number Of Converters
1
Power Dissipation (max)
22.5mW
Voltage Supply Source
Single Supply
Operating Temperature
-40°C ~ 85°C
Lead Free Status / RoHS Status
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD7898AR-10
Manufacturer:
ADI/亚德诺
Quantity:
20 000
REV. A
Pin
No.
1
2
3
4
5
6
7
8
Pin
Mnemonic
REF IN
V
GND
SCLK
SDATA
V
CS/CONVST
V
IN
DRIVE
DD
Function
Voltage Reference Input. An external reference source should be connected to this pin to provide the
reference voltage for the AD7898’s conversion process. The REF IN input is buffered on-chip. The
nominal reference voltage for correct operation of the AD7898 is 2.5 V ± 5%. A 0.1 µF capacitor
should be placed on the REF IN pin.
Analog Input Channel. The analog input range is ± 10 V (AD7898-10) and ± 2.5 V (AD7898-3).
Analog Ground. Ground reference for track/hold, comparator, digital circuitry, and DAC.
Serial Clock Input. An external serial clock is applied to this input to obtain serial data from the AD7898.
When in Mode 0 operation, a new serial data bit is clocked out on the falling edge of this serial clock.
In Mode 0, data is guaranteed valid for 20 ns after this falling edge so that data can be accepted on the
falling edge when a fast serial clock is used. The serial clock input should be taken low at the end of
the serial data transmission. When in Mode 1 operation, SCLK also provides the serial clock for
accessing data from the part as in Mode 0, but this clock input is also used as the clock source for the
AD7898’s conversion process when in Mode 1.
Serial Data Output. Serial data from the AD7898 is provided at this output. The serial data is clocked
out by the falling edge of SCLK, but the data can also be read on the falling edge of SCLK. This is
possible because data bit N is valid for a specified time after the falling edge of SCLK (data hold time).
Sixteen bits of serial data are provided with four leading zeros followed by the 12 bits of conversion data,
which is provided MSB first. On the 16th falling edge of SCLK, the SDATA line is held for the data
hold time and then is disabled (three-stated). Output data coding is two’s complement for the AD7898.
Logic Power Supply Input. The voltage supplied at this pin determines at what voltage the serial inter-
face of the AD7898 will operate.
Chip Select/Convert Start. This pin is CONVST, an edge-triggered logic input when in Mode 0 operation.
On the falling edge of this input, the track/hold goes into its hold mode, and conversion is initiated.
When in Mode 1 operation, this pin is Chip Select, an active low logic input. This input provides the
dual function of initiating conversions on the AD7898 and also frames the serial data transfer.
Power Supply Input, 5 V ± 5%.
PIN FUNCTION DESCRIPTIONS
–5–
AD7898