AD9517-2A/PCBZ Analog Devices Inc, AD9517-2A/PCBZ Datasheet - Page 39
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD9517-2A/PCBZ
Manufacturer Part Number
AD9517-2A/PCBZ
Description
12-Output Clock Generator With 2.8GHz VC
Manufacturer
Analog Devices Inc
Datasheet
1.AD9517-2ABCPZ-RL7.pdf
(80 pages)
Specifications of AD9517-2A/PCBZ
Main Purpose
Timing, Clock Generator
Embedded
No
Utilized Ic / Part
AD9517-2A
Primary Attributes
2 Inputs, 12 Outputs, 2.2GHz VCO
Secondary Attributes
CMOS, LVPECL & LVDS Compatible
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
VCO Calibration
The AD9517 on-chip VCO must be calibrated to ensure proper
operation over process and temperature. The VCO calibration
is controlled by a calibration controller running off of a divided
REFIN clock. The calibration requires that the PLL be set up
properly to lock the PLL loop and that the REFIN clock be present.
During the first initialization after a power-up or a reset of the
AD9517, a VCO calibration sequence is initiated by setting
Register 0x018[0] = 1b. This can be done as part of the initial
setup before executing update registers (Register 0x232[0] = 1b).
Subsequent to the initial setup, a VCO calibration sequence is
initiated by resetting Register 0x018[0] = 0b, executing an update
registers operation, setting Register 0x018[0] = 1b, and executing
another update registers operation. The readback bit (Register
0x1F[6]) indicates when a VCO calibration is finished by returning
a logic true (that is, 1b).
The sequence of operations for the VCO calibration is:
•
•
•
•
•
•
•
•
REFIN (REF1)
REFIN (REF2)
Program the PLL registers to the proper values for the PLL
loop. Note that that automatic holdover mode must be
disabled, and the VCO divider must not be set to “Static. ”
Ensure that the input reference signal is present.
For the initial setting of the registers after a power-up or reset,
initiate VCO calibration by setting Register 0x018[0] = 1b.
Subsequently, whenever a calibration is desired, set
Register 0x018[0] = 0b, update registers; and set Register
0x018[0] = 1b, update registers.
A SYNC operation is initiated internally, causing the
outputs to go to a static state determined by normal SYNC
function operation.
VCO calibrates to the desired setting for the requested
VCO frequency.
Internally, the SYNC signal is released, allowing outputs to
continue clocking.
PLL loop is closed.
PLL locks.
BYPASS
CLK
CLK
LF
REF1
REF2
REGULATOR (LDO)
LOW DROPOUT
VCO
SWITCHOVER
STATUS
REFERENCE
REF_SEL
STATUS
VS
PRESCALER
2, 3, 4, 5, OR 6
1
P, P + 1
DIVIDE BY
GND
0
N DIVIDER
DIVIDER
Figure 53. Reference and VCO Status Monitors
R
COUNTERS
DISTRIBUTION
REFERENCE
A/B
RSET
Rev. B | Page 39 of 80
0
1
VCO STATUS
PROGRAMMABLE
PROGRAMMABLE
R DELAY
N DELAY
REFMON
A SYNC is executed during the VCO calibration; therefore,
the outputs of the AD9517 are held static during the calibration,
which prevents unwanted frequencies from being produced.
However, at the end of a VCO calibration, the outputs may
resume clocking before the PLL loop is completely settled.
The VCO calibration clock divider is set as shown in Table 54
(Register 0x018[2:1]).
The calibration divider divides the PFD frequency (reference
frequency divided by R) down to the calibration clock. The
calibration occurs at the PFD frequency divided by the
calibration divider setting. Lower VCO calibration clock
frequencies result in longer times for a calibration to be
completed.
The VCO calibration clock frequency is given by
where:
f
R is the value of the R divider.
cal_div is the division set for the VCO calibration divider
(Register 0x018[2:1]).
The VCO calibration takes 4400 calibration clock cycles.
Therefore, the VCO calibration time in PLL reference clock
cycles is given by
Table 29. Example Time to Complete a VCO Calibration
with Different f
f
100
10
10
REFIN
REFIN
f
Time to Calibrate VCO =
4400 × R × cal_div PLL Reference Clock Cycles
(MHz)
is the frequency of the REFIN signal.
CAL_CLOCK
= f
R Divider
1
10
100
FREQUENCY
REFIN
DETECTOR
REFIN
DETECT
PHASE
LOCK
/(R × cal_div)
Frequencies
PFD
100 MHz
1 MHz
100 kHz
CPRSET VCP
CHARGE
PUMP
HOLD
Time to Calibrate VCO
88 μs
8.8 ms
88 ms
AD9517-2
LD
CP
STATUS