ADF4113HVBRUZ-RL Analog Devices Inc, ADF4113HVBRUZ-RL Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
ADF4113HVBRUZ-RL
Manufacturer Part Number
ADF4113HVBRUZ-RL
Description
IC,FREQUENCY SYNTHESIZER,BICMOS,TSSOP,16PIN,PLASTIC
Manufacturer
Analog Devices Inc
Type
Clock/Frequency Synthesizer (RF)r
Datasheet
1.ADF4113HVBCPZ.pdf
(20 pages)
Specifications of ADF4113HVBRUZ-RL
Pll
Yes
Input
CMOS
Output
Clock
Number Of Circuits
1
Ratio - Input:output
2:1
Differential - Input:output
Yes/No
Frequency - Max
4GHz
Divider/multiplier
Yes/No
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
16-TSSOP
Frequency-max
4GHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
EVAL-ADF4113HVEB1Z - BOARD EVALUATION FOR ADF4113HVEVAL-ADF4113EBZ2 - BOARD EVAL FOR ADF4113 1750MHZEVAL-ADF4113EBZ1 - BOARD EVAL FOR ADF4113EVAL-ADF411XEBZ1 - BOARD EVAL FOR ADF411X NO CHIP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
ADF4113HV
PHASE FREQUENCY DETECTOR (PFD) AND
CHARGE PUMP
The PFD takes inputs from the R counter and N counter and
produces an output proportional to the phase and frequency
difference between them. Figure 17 is a simplified schematic.
The PFD includes a programmable delay element that controls
the width of the antibacklash pulse. This pulse ensures that
there is no dead zone in the PFD transfer function and mini-
mizes phase noise and reference spurs. Two bits in the reference
counter latch, ABP2 and ABP1, control the width of the pulse.
See Figure 20. The only recommended setting for the antiback-
lash pulse width is 7.2 ns.
CP OUTPUT
MUXOUT AND LOCK DETECT
The output multiplexer on the ADF4113HV allows the user to
access various internal points on the chip. The state of MUXOUT
is controlled by M3, M2, and M1 in the function latch. Figure 22
shows the full truth table (function latch map). Figure 18 shows
the MUXOUT section in block diagram form.
R DIVIDER
N DIVIDER
R DIVIDER
N DIVIDER
HIGH
HIGH
Figure 17. PFD Simplified Schematic and Timing (in Lock)
D1
D2
CLR1
CLR2
U2
U1
Q2
Q1
PROGRAMMABLE
ABP1
UP
DOWN
DELAY
ABP2
U3
CPGND
V
P
CHARGE
PUMP
CP
Rev. A | Page 10 of 20
ANALOG LOCK DETECT
Lock Detect
MUXOUT can be programmed for two types of lock detect:
digital lock detect and analog lock detect.
Digital lock detect is active high. When LDP in the AB counter
latch is set to 0, digital lock detect is set high when the phase
error on five consecutive phase detector (PD) cycles is less than
10 ns. With LDP set to 1, five consecutive cycles of less than
3 ns are required to set the lock detect. It stays high until a phase
error greater than 25 ns is detected on any subsequent PD cycle.
Operate the N-channel, open-drain, analog lock detect with a
10 kΩ nominal external pull-up resistor. When lock has been
detected, this output is high with narrow low-going pulses.
INPUT SHIFT REGISTER
The ADF4113HV digital section includes a 24-bit input shift
register, a 14-bit R counter, and a 19-bit N counter comprising
a 6-bit A counter and a 13-bit B counter. Data is clocked into
the 24-bit shift register on each rising edge of CLK, MSB first.
Data is transferred from the shift register to one of three latches
on the rising edge of LE. The destination latch is determined by
the state of the two control bits (C2, C1) in the shift register.
These are the two LSBs, DB1 and DB0, as shown in Figure 2.
The truth table for these bits is shown in Table 6. Figure 19
shows a summary of how the latches are programmed.
Table 6. C2, C1 Truth Table
C2
0
0
1
DIGITAL LOCK DETECT
R COUNTER OUTPUT
N COUNTER OUTPUT
Control Bits
C1
0
1
0
SDOUT
R counter
N counter (A and B)
Function latch (including prescaler)
Data Latch
Figure 18. MUXOUT Circuit
MUX
CONTROL
DV
DGND
DD
MUXOUT