ADSP-21262SBBC-150 Analog Devices Inc, ADSP-21262SBBC-150 Datasheet - Page 17

• Manufacturer Part Number: ADSP-21262SBBC-150
• Description: IC,DSP,32-BIT,CMOS,BGA,136PIN,PLASTIC
• Manufacturer: Analog Devices Inc
• Series: SHARC®r
• Type: Fixed/Floating Pointr

Specifications of ADSP-21262SBBC-150

• Interface: DAI, SPI
• Clock Rate: 150MHz
• Non-volatile Memory: ROM (512 kB)
• On-chip Ram: 256kB
• Voltage - I/o: 3.30V
• Voltage - Core: 1.20V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 136-CSPBGA
• Device Core Size: 32/40Bit
• Architecture: Super Harvard
• Format: Floating Point
• Clock Freq (max): 150MHz
• Mips: 150
• Device Input Clock Speed: 150MHz
• Ram Size: 256KB
• Program Memory Size: 512KB
• Operating Supply Voltage (typ): 1.2/3.3V
• Operating Supply Voltage (min): 1.14/3.13V
• Operating Supply Voltage (max): 1.26/3.47V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 136
• Package Type: CSPBGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Power-Up Sequencing
The timing requirements for DSP startup are given in
and
approximately 200 A may be observed on the RESET pin. This
leakage current results from the weak internal pull-up resistor
on this pin being enabled during power-up.
Table 15. Power-Up Sequencing (DSP Startup)
1
2
3
4
5
Parameter
Timing Requirements
t
t
t
t
t
Switching Characteristics
t
Valid V
Assumes a stable CLKIN signal, after meeting worst-case startup timing of crystal oscillators. Refer to the crystal oscillator manufacturer’s data sheet for startup time.
Based on CLKIN cycles.
Applies after the power-up sequence is complete. Subsequent resets require a minimum of four CLKIN cycles for RESET to be held low in order to properly initialize and
The 4096 cycle count depends on t
RSTVDD
IVDDEVDD
CLKVDD
CLKRST
PLLRST
CORERST
depending on the design of the power supply subsystem.
Assume a 25 ms maximum oscillator startup time if using the XTAL pin and internal oscillator circuit in conjunction with an external crystal.
propagate default states at all I/O pins.
4097 cycles maximum.
Figure
DDINT
5. Note that during power-up, a leakage current of
/V
(MULTIPLEXED WITH CLKOUT)
DDEXT
assumes that the supplies are fully ramped to their 1.2 V and 3.3 V rails. Voltage ramp rates can vary from microseconds to hundreds of milliseconds
RESETOUT
RESET Low Before V
V
CLKIN Valid After V
CLKIN Valid Before RESET Deasserted
PLL Control Setup Before RESET Deasserted
DSP Core Reset Deasserted After RESET Deasserted
DDINT
CLK_CFG1–0
SRST
On Before V
V
RESET
V
specification in
CLKIN
DDEXT
DDINT
DDEXT
DDINT
DDINT
Table
/V
/V
t
RSTVDD
DDEXT
DDEXT
17. If setup time is not met, one additional CLKIN cycle can be added to the core reset time, resulting in
Valid
Rev. F | Page 17 of 44 | July 2009
On
Figure 5. Power-Up Sequencing
Table 15
1
t
IVDDEVDD
t
PLLRST
ADSP-21261/ADSP-21262/ADSP-21266
t
t
CLKVDD
CLKRST
Min
0
–50
0
10
20
4096 t
2
3
CK
t
CORERST
4, 5
Max
+200
200
Unit
ns
ms
ms
μs
μs