ADUM3160BRWZ-RL Analog Devices Inc, ADUM3160BRWZ-RL Datasheet - Page 4

• Manufacturer Part Number: ADUM3160BRWZ-RL
• Description: 2.5kVFull/Low Speed USB Digital Isolator
• Manufacturer: Analog Devices Inc
• Series: iCoupler®r

Specifications of ADUM3160BRWZ-RL

• Operating Temperature: -40°C ~ 105°C
• Inputs - Side 1/side 2: 2/2
• Number Of Channels: 4
• Isolation Rating: 2500Vrms
• Voltage - Supply: 3 V ~ 5.5 V
• Data Rate: 12Mbps
• Propagation Delay: 70ns
• Output Type: Logic
• Package / Case: 16-SOIC (0.300", 7.50mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ADuM3160
Parameter
1
2
3
4
PACKAGE CHARACTERISTICS
Table 2.
Parameter
Resistance (Input to Output)
Capacitance (Input to Output)
Input Capacitance
IC Junction-to-Ambient Thermal Resistance
1
2
REGULATORY INFORMATION
The ADuM3160 has been approved by the organizations listed in Table 3. See Table 10 and the Insulation Lifetime section for details
regarding recommended maximum working voltages for specific cross-isolation waveforms and insulation levels.
Table 3.
UL
Recognized Under 1577 Component
Single Protection 2500 V rms Isolation
File E214100
1
2
3
C
The supply current values for the device running at a fixed continuous data rate 50% duty cycle, alternating J and K states. Supply current values are specified with
Propagation delay of the low speed DD+ to UD+ or DD− to UD− in either signal direction is measured from the 50% level of the rising or falling edge to the 50% level
of the rising or falling edge of the corresponding output signal.
CM
that can be sustained while maintaining V
magnitude is the range over which the common mode is slewed.
The device is considered a 2-terminal device; Pin 1, Pin 2, Pin 3, Pin 4, Pin 5, Pin 6, Pin 7, and Pin 8 are shorted together and Pin 9, Pin 10, Pin 11, Pin 12, Pin 13, Pin 14,
Pin 15, and Pin 16 are shorted together.
Input capacitance is from any input data pin to ground.
In accordance with UL 1577, each ADuM3160 is proof tested by applying an insulation test voltage ≥3000 V rms for 1 sec (current leakage detection limit = 10 µA).
In accordance with DIN V VDE V 0884-10, each ADuM3160 is proof tested by applying an insulation test voltage ≥1050 V peak for 1 sec (partial discharge detection
limit = 5 pC). The * marking branded on the component indicates DIN V VDE V 0884-10 approval.
See Table 8 for recommended maximum working voltages under various operating conditions.
USB-compliant load present.
L
Recognition Program
Voltage
For All Operating Modes
= load capacitance, R
H
Common-Mode Transient Immunity
Common-Mode Transient Immunity
is the maximum common-mode voltage slew rate that can be sustained while maintaining V
at Logic High Output
at Logic Low Output
2
L
= test load resistance, V
1
4
4
1
1
O
< 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges. The transient
L
CSA
Approved under CSA Component Acceptance
Notice #5A
Basic insulation per CSA 60950-1-07 and IEC 60950-1,
2
voltage
File 205078
= test load voltage, and V
nd
ed., 600 V rms (849 V peak) maximum working
3
Symbol
|CM
|CM
Symbol
R
C
C
θ
JA
I-O
I-O
I
H
L
|
|
Rev. A | Page 4 of 16
CM
= common-mode voltage.
Min
25
25
Min
Typ
35
35
Typ
10
2.2
4.0
45
12
O
> 0.8 V
Max
Max
DD2
. CM
Unit
kV/µs
kV/µs
L
Unit
Ω
pF
pF
°C/W
is the maximum common-mode voltage slew rate
VDE
Certified according to DIN V VDE V
0884-10 (VDE V 0884-10):2006-12
Reinforced insulation, 560 V peak
File 2471900-4880-0001
Test Conditions
V
V
800 V
V
1000 V, transient magnitude = 800 V
Test Conditions
f = 1 MHz
Thermocouple located at center of
package underside
UD+
CM
UD+
= 1000 V, transient magnitude =
, V
, V
UD−
UD−
, V
, V
DD+
DD+
, V
, V
1
DD−
DD−
= V
= 0 V, V
DD1
or V
CM
2
=
DD2
,