ADV7179KCP Analog Devices Inc, ADV7179KCP Datasheet - Page 25
![IC,TV/VIDEO CIRCUIT,Video Encoder,LLCC,40PIN,CERAMIC](/photos/6/50/65062/505-40-lfcsp_sml.jpg)
ADV7179KCP
Manufacturer Part Number
ADV7179KCP
Description
IC,TV/VIDEO CIRCUIT,Video Encoder,LLCC,40PIN,CERAMIC
Manufacturer
Analog Devices Inc
Type
Video Encoderr
Datasheet
1.ADV7179KCPZ.pdf
(52 pages)
Specifications of ADV7179KCP
Rohs Status
RoHS non-compliant
Applications
Digital Cameras, Mobile Phones, Portable Video
Voltage - Supply, Analog
2.8 V, 3.3 V
Mounting Type
Surface Mount
Package / Case
40-LFCSP
Voltage - Supply, Digital
-
Lead Free Status / RoHS Status
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADV7179KCP
Manufacturer:
AD
Quantity:
1 303
Company:
Part Number:
ADV7179KCP
Manufacturer:
ADI
Quantity:
244
Company:
Part Number:
ADV7179KCPZ
Manufacturer:
ADI
Quantity:
250
Part Number:
ADV7179KCPZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
ADV7179KCPZ-REE1
Manufacturer:
SARC
Quantity:
92
Company:
Part Number:
ADV7179KCPZ-REEL
Manufacturer:
TI
Quantity:
69 456
Part Number:
ADV7179KCPZ-REEL
Manufacturer:
ADI/亚德诺
Quantity:
20 000
POWER-ON RESET
After power-up, it is necessary to execute a reset operation. A
reset occurs on the falling edge of a high-to-low transition on
the RESET pin. This initializes the pixel port so that the pixel
inputs, P7–P0, are selected. After reset, the ADV7174/ADV7179
are automatically set up to operate in NTSC mode. Subcarrier
frequency code 21F07C16H is loaded into the subcarrier
frequency registers. All other registers, with the exceptions of
Mode Register 1 and Mode Register 4, are set to 00H. Bit MR44
of Mode Register 4 is set to Logic 1. This enables the 7.5 IRE
pedestal. Bit MR13, DAC A, and Bit MR16, DAC C, are powered
down by default.
SCH PHASE MODE
The SCH phase is configured in default mode to reset every
four (NTSC) or eight (PAL) fields to avoid an accumulation of
SCH phase error over time. In an ideal system, 0 SCH phase
error would be maintained forever, but in reality, this is
impossible to achieve due to clock frequency variations. This
effect is reduced by the use of a 32-bit DDS, which generates
this SCH.
Resetting the SCH phase every four or eight fields avoids the
accumulation of SCH phase error and results in very minor
SCH phase jumps at the start of the 4- or 8-field sequence.
Resetting the SCH phase should not be done if the video source
does not have stable timing or the ADV7174/ADV7179 is
configured in RTC mode (MR21 = 1 and MR22 = 1). Under
these conditions (unstable video), the subcarrier phase reset
should be enabled (MR22 = 0 and MR21 = 1), but no reset
applied. In this configuration, the SCH phase can never be
reset, which means that the output video can now track the
unstable input video. The subcarrier phase reset, when applied,
resets the SCH phase to Field 0 at the start of the next field, for
example, subcarrier phase reset applied in Field 5 (PAL) on the
start of the next field SCH phase is reset to Field 0.
MPU PORT DESCRIPTION
The ADV7174/ADV7179 supports a 2-wire serial (I
compatible) microprocessor bus driving multiple peripherals.
Two inputs, serial data (SDATA) and serial clock (SCLOCK),
carry information between any device connected to the bus.
Each slave device is recognized by a unique address. The
ADV7174/ADV7179 has four possible slave addresses for both
read and write operations. These are unique addresses for each
device and are illustrated in Figure 33 and Figure 34. The LSB
sets either a read or write operation. Logic 1 corresponds to a
read operation, while Logic 0 corresponds to a write operation.
A 1 is set by setting the ALSB pin of the ADV7174/ ADV7179
to Logic 0 or Logic 1.
2
C
Rev. B | Page 25 of 52
To control the various devices on the bus, the following
protocol must be followed: first, the master initiates a data
transfer by establishing a start condition, defined by a high-to-
low transition on SDATA while SCLOCK remains high. This
indicates that an address/data stream will follow. All peripherals
respond to the start condition and shift the next eight bits (7-bit
address + R/ W bit). The bits transfer from MSB down to LSB.
The peripheral that recognizes the transmitted address
responds by pulling the data line low during the ninth clock
pulse. This is known as an Acknowledge bit. All other devices
withdraw from the bus at this point and maintain an idle
condition. The idle condition is where the device monitors the
SDATA and SCLOCK lines waiting for the start condition and
the correct transmitted address. The R/ W bit determines the
direction of the data. A Logic 0 on the LSB of the first byte
means that the master will write information to the peripheral.
A Logic 1 on the LSB of the first byte means that the master will
read information from the peripheral.
The ADV7174/ADV7179 acts as a standard slave device on the
bus. The data on the SDATA pin is eight bits long, supporting
the 7-bit addresses plus the R/ W bit. The ADV7174/ADV7179
has 26 subaddresses to enable access to the internal registers. It
therefore interprets the first byte as the device address and the
second byte as the starting subaddress. The subaddresses’ auto
increment allows data to be written to or read from the starting
subaddress. A data transfer is always terminated by a stop
condition. The user can also access any unique subaddress
register on a one-by-one basis without having to update all the
registers. There is one exception. The subcarrier frequency
registers should be updated in sequence, starting with
Subcarrier Frequency Register 0. The auto increment function
should then be used to increment and access Subcarrier
1
0
1
1
0
0
Figure 33. ADV7174 Slave Address
Figure 34. ADV7179 Slave Address
1
1
0
0
ADV7174/ADV7179
1
1
SET UP BY
SET UP BY
ADDRESS
CONTROL
ADDRESS
CONTROL
ALSB
ALSB
A1
A1
READ/WRITE
READ/WRITE
0
1
0
1
CONTROL
CONTROL
X
X
WRITE
READ
WRITE
READ