CAT5241YI-10-T2 ON Semiconductor, CAT5241YI-10-T2 Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
CAT5241YI-10-T2
Manufacturer Part Number
CAT5241YI-10-T2
Description
DPP NV, QUAD 64 TAPS, I2C
Manufacturer
ON Semiconductor
Datasheet
1.CAT5241YI-10-T2.pdf
(16 pages)
CAT5241
PIN DESCRIPTION
PIN DESCRIPTION
SCL: Serial Clock
The CAT5241 serial clock input pin is used to clock
all data transfers into or out of the device.
SDA: Serial Data
The CAT5241 bidirectional serial data pin is used to
transfer data into and out of the device. The SDA pin
is an open drain output and can be wire-or'd with the
other open drain or open collector outputs.
A0, A1, A2, A3: Device Address Inputs
These
addressing multiple devices. A total of sixteen
devices can be addressed on a single bus. A match
in the slave address must be made with the address
input in order to initiate communication with the
CAT5241.
R
The four sets of R
terminal connections on a mechanical potentiometer.
R
The four R
of a mechanical potentiometer.
Doc. No. MD-2011 Rev. R
H
W
Pin (SOIC)
, R
: Wiper
L
10
11
12
13
14
15
16
17
18
19
20
: Resistor End Points
1
2
3
4
5
6
7
8
9
inputs
W
pins are equivalent to the wiper terminal
Name
set
GND
SDA
SCL
R
R
R
R
V
H
R
R
R
R
R
R
R
R
A0
A2
A3
A1
W0
W1
W2
W3
CC
L0
H0
L1
H1
H2
L2
H3
L3
and R
the
Device Address, LSB
Serial Data Input/Output
Function
Wiper Terminal for Potentiometer 0
Low Reference Terminal for Potentiometer 0
High Reference Terminal for Potentiometer 0
Device Address
Wiper Terminal for Potentiometer 1
Low Reference Terminal for Potentiometer 1
High Reference Terminal for Potentiometer 1
Ground
High Reference Terminal for Potentiometer 2
Low Reference Terminal for Potentiometer 2
Wiper Terminal for Potentiometer 2
Bus Serial Clock
Device Address
Device Address
High Reference Terminal for Potentiometer 3
Low Reference Terminal for Potentiometer 3
Wiper Terminal for Potentiometer 3
Supply Voltage
L
pins are equivalent to the
device
address
when
2
DEVICE OPERATION
The CAT5241 is four resistor arrays integrated with I²C
serial interface logic, four 6-bit wiper control registers
and sixteen 6-bit, non-volatile memory data registers.
Each resistor array contains 63 separate resistive
elements connected in series. The physical ends of
each array are equivalent to the fixed terminals of a
mechanical potentiometer (R
symmetrical and may be interchanged. The tap
positions between and at the ends of the series resis–
tors are connected to the output wiper terminals (R
a CMOS transistor switch. Only one tap point for each
potentiometer is connected to its wiper terminal at a
time and is determined by the value of the wiper control
register. Data can be read or written to the wiper control
registers or the non-volatile memory data registers via
the I²C bus. Additional instructions allow data to be
transferred between the wiper control registers and
each
registers. Also, the device can be instructed to operate
in an "increment/decrement" mode.
respective
potentiometer's
Characteristics subject to change without notice
H
and R
© 2009 SCILLC. All rights reserved.
non-volatile
L
). R
H
and R
W
L
data
) by
are