CAT5241YI-10-T2 ON Semiconductor, CAT5241YI-10-T2 Datasheet - Page 3

• Manufacturer Part Number: CAT5241YI-10-T2
• Description: DPP NV, QUAD 64 TAPS, I2C
• Manufacturer: ON Semiconductor

ABSOLUTE MAXIMUM RATINGS
Recommended Operating Conditions
V
POTENTIOMETER CHARACTERISTICS
Over recommended operating conditions unless otherwise stated.
Notes:
(1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings
(2) The minimum DC input voltage is –0.5 V. During transitions, inputs may undershoot to –2.0 V for periods of less than 20 ns. Maximum
(3) Latch-up protection is provided for stresses up to 100mA on address and data pins from –1 V to V
(4) This parameter is tested initially and after a design or process change that affects the parameter.
(5) Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a
(6) Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a
(7) LSB = R
(8) n = 0, 1, 2, ..., 63
© 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
Parameter
Temperature Under Bias
Storage Temperature
Voltage on any Pin with Respect to V
V
Package Power Dissipation Capability (T
Lead Soldering Temperature (10 s)
Wiper Current
Parameter
Operating Ambient Temperature (Industrial)
cc
C
Symbol Parameter
TC
TC
CC
H
V
only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this
specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability.
DC voltage on output pins is V
potentiometer.
potentiometer. It is a measure of the error in step size.
= +2.5 V to +6 V
R
R
R
R
/C
R
R
TERM
V
I
fc
POT
POT
POT
POT
RATIO
with Respect to Ground
W
RPOT
W
W
N
L
/C
W
TOT
Potentiometer Resistance (-00)
Potentiometer Resistance (-50)
Potentiometer Resistance (-10)
Potentiometer Resistance (-25)
Potentiometer Resistance Tolerance
R
Power Rating
Wiper Current
Wiper Resistance
Wiper Resistance
Voltage on any R
Noise
Resolution
Absolute Linearity
Relative Linearity
Temperature Coefficient of R
Ratiometric Temp. Coefficient
Potentiometer Capacitances
Frequency Response
/ 63 or (R
POT
Matching
H
- R
L
) / 63, single pot
CC
H
+0.5 V, which may overshoot to V
(6)
(5)
or R
L
Pin
SS
(2)(3)
POT
(1)
A
= 25°C)
I
R
I
W
W
W(n)(actual)
-2.0 to +V
R
= ±3 mA @ V
= ±3 mA @ V
Test Conditions
W(n+1)
R
3
25°C, each pot
-55 to +125
-65 to +150
-2.0 to +7.0
CC
-40 to +85
POT
Ratings
Ratings
+2.0 V for periods of less than 20 ns.
V
300
±12
1.0
SS
- [R
= 50 kΩ
- R
(4)
(4)
(4)
(4)
= 0 V
CC
W(n)+LSB
(n)(expected)
+2.0
CC
CC
(4)
= 5 V
=3 V
]
(8)
Units
Units
(8)
mA
°C
°C
°C
°C
W
V
V
GND
Min
CC
+ 1 V.
10/10/25
±300
TBD
Typ
100
2.5
1.6
0.4
50
10
80
Doc. No. MD-2011 Rev. R
Max
±0.2
±20
300
150
V
50
±6
±1
20
1
CC
CAT5241
ppm/°C
ppm/°C
nV/√Hz
LSB
LSB
Units
MHz
mW
mA
kΩ
kΩ
kΩ
kΩ
pF
%
%
%
Ω
Ω
(7)
(7)