CS5461A-ISZR Cirrus Logic Inc, CS5461A-ISZR Datasheet - Page 20

• Manufacturer Part Number: CS5461A-ISZR
• Description: IC Sngl-Phs Bi-Directional Power/Energy
• Manufacturer: Cirrus Logic Inc

Specifications of CS5461A-ISZR

• Input Impedance: 30 KOhm
• Measurement Error: 0.1%
• Voltage - I/o High: 0.8V
• Voltage - I/o Low: 0.2V
• Current - Supply: 2.9mA
• Voltage - Supply: 4.75 V ~ 5.25 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-SSOP
• Meter Type: Single Phase
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1552 - BOARD EVAL & SOFTWARE CS5461A
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

The Cycle Count Register (N) must be set to a value
greater than one. Status bit TUP in the Status Register,
indicates when the Temperature Register is updated.
The Temperature Offset Register sets the zero-degree
measurement. To improve temperature measurement
accuracy, the zero-degree offset should be adjusted af-
ter the CS5461A is initialized. Temperature offset cali-
bration is achieved by adjusting the Temperature Offset
Register (T
sured from a calibrated digital thermometer and the
CS5461A temperature sensor. A one-degree adjust-
ment to the Temperature Register (T) is achieved by
adding 2.737649x10
ter (T
if T
or 0xF3C168 (2’s compliment notation) is stored in the
Temperature Offset Register (T
To convert the Temperature Register (T) from a Celsius
scale (
Applying the above relationship to the CS5461A tem-
perature measurement algorithm
If T
scale, then the modified values are T
(0xF460E1) and T
Fahrenheit scale.
5.8 Voltage Reference
The CS5461A is specified for operation with a +2.5 V
reference between the VREFIN and AGND pins. To uti-
lize the on-chip 2.5 V reference, connect the VREFOUT
pin to the VREFIN pin of the device. The VREFIN pin
can be used to connect external filtering and/or refer-
ences.
5.9 System Initialization
Upon powering up, the digital circuitry is held in reset
until the analog voltage reaches 4.0 V. At that time, an
eight-XIN-clock-period delay is enabled to allow the os-
cillator to stabilize. The CS5461A will then initialize.
20
T
〈 〉
off
o
off
F
off
= -0.0951126 and ∆T = -2.0 (
T off
o
= -0.09566 and T
=
). Therefore,
C) to a Fahrenheit scale (
(
9
-- -
5
=
×
off
–
0.0951126
T
) by the differential temperature (∆T) mea-
gain
T off
)
=
[
T
T off
o
〈 〉
+
F
gain
-4
o
C
– (
=
to the Temperature Offset Regis-
+
2.0
9
-- - C
5
+
= 42.3132 (0x54A05E) for a
∆ (
(
(
o
gain
T
×
T
off
2.737649
×
+
2.737649
17.7778
= 23.507
+
(
off
17.7778
o
).
F) utilize the formula
⋅
o
)
10
⋅
C), then
10
–
4
×
–
off
)
4
2.737649 10
)
=
for a Celsius
= -0.0907935
–
0.09566
⋅
–
4
)
)
]
A hardware reset is initiated when the RESET pin is as-
serted with a minimum pulse width of 50 ns. The
RESET signal is asynchronous, with a Schmitt-trigger
input. Once the RESET pin is de-asserted, an
eight-XIN-clock-period delay is enabled.
A software reset is initiated by writing the command of
0x80. After a hardware or software reset, the internal
registers (some of which drive output pins) will be reset
to their default values. Status bit DRDY in the Status
Register, indicates the CS5461A is in its active state
and ready to receive commands.
5.10 Power-down States
The CS5461A has two power-down states, stand-by
and sleep. In the stand-by state all circuitry except the
voltage reference and crystal oscillator is turned off. To
return the device to the active state a power-up com-
mand is sent to the device.
In sleep state all circuitry except the instruction decoder
is turned off. When the power-up command is sent to
the device, a system initialization is performed (see
Section 5.9 System Initialization
5.11 Oscillator Characteristics
The XIN and XOUT pins are the input and output of an
inverting amplifier configured as an on-chip oscillator,
as shown in Figure 8. The oscillator circuit is designed
to work with a quartz crystal. To reduce circuit cost, two
load capacitors C1 and C2 are integrated in the device,
from XIN to DGND, and XOUT to DGND. PCB trace
lengths should be minimized to reduce stray capaci-
tance. To drive the device from an external clock
source, XOUT should be left unconnected while XIN is
driven by the external circuitry. There is an amplifier be-
tween XIN and the digital section which provides
CMOS-level signals. This amplifier works with sinusoi-
Figure 8. Oscillator Connection
DGND
XOUT
XIN
C1
C2
C1 =
on page 20).
C2 =
Oscillator
22 pF
Circuit
CS5461A
DS661F2