KSZ8041FTLI Micrel Inc, KSZ8041FTLI Datasheet - Page 27
![Physical Layer Transceiver 10/100BASE-FX ( )](/photos/6/84/68454/576-48-tqfp_sml.jpg)
KSZ8041FTLI
Manufacturer Part Number
KSZ8041FTLI
Description
Physical Layer Transceiver 10/100BASE-FX ( )
Manufacturer
Micrel Inc
Type
Transceiverr
Datasheet
1.KSZ8041MLLI.pdf
(65 pages)
Specifications of KSZ8041FTLI
Number Of Drivers/receivers
1/1
Protocol
SMII
Voltage - Supply
3.135 V ~ 3.465 V
Mounting Type
Surface Mount
Package / Case
48-TQFP, 48-VQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
576-3294 - BOARD EVALUATION KSZ8041FTL
Lead Free Status / RoHS Status
Compliant, Lead free / RoHS Compliant
Other names
576-3347
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
KSZ8041FTLI
Manufacturer:
MICREL
Quantity:
5 000
Part Number:
KSZ8041FTLI-TR
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Micrel, Inc.
Receive Data Valid (RXDV)
RXDV is driven by the PHY to indicate that the PHY is presenting recovered and decoded nibbles on RXD[3:0].
RXDV transitions synchronously with respect to RXC.
Receive Data [3:0] (RXD[3:0])
RXD[3:0] transitions synchronously with respect to RXC. For each clock period in which RXDV is asserted, RXD[3:0]
transfers a nibble of recovered data from the PHY.
Receive Error (RXER)
RXER is asserted for one or more RXC periods to indicate that a Symbol Error (e.g. a coding error that a PHY is capable
of detecting, and that may otherwise be undetectable by the MAC sub-layer) was detected somewhere in the frame
presently being transferred from the PHY.
RXER transitions synchronously with respect to RXC. While RXDV is de-asserted, RXER has no effect on the MAC.
Carrier Sense (CRS)
CRS is asserted and de-asserted as follows:
Collision (COL)
COL is asserted in half-duplex mode whenever the transmitter and receiver are simultaneously active on the line. This is
used to inform the MAC that a collision has occurred during its transmission to the PHY.
COL transitions asynchronously with respect to TXC and RXC.
Reduced MII (RMII) Data Interface (KSZ8041TL/FTL only)
The Reduced Media Independent Interface (RMII) specifies a low pin count Media Independent Interface (MII). It provides
a common interface between physical layer and MAC layer devices, and has the following key characteristics:
The KSZ8041TL/FTL is configured in RMII mode after it is power-up or reset with the following:
In RMII mode, unused MII signals, TXD[3:2] (pins 39, 38), are tied to ground.
December 2009
x
x
x
x
x
x
x
x
x
x
In 10Mbps mode, RXDV is asserted with the first nibble of the SFD (Start of Frame Delimiter), “5D”, and remains
asserted until the end of the frame.
In 100Mbps mode, RXDV is asserted from the first nibble of the preamble to the last nibble of the frame.
In 10Mbps mode, CRS assertion is based on the reception of valid preambles. CRS de-assertion is based on the
reception of an end-of-frame (EOF) marker.
In 100Mbps mode, CRS is asserted when a start-of-stream delimiter, or /J/K symbol pair is detected. CRS is de-
asserted when an end-of-stream delimiter, or /T/R symbol pair is detected. Additionally, the PMA layer de-asserts
CRS if IDLE symbols are received without /T/R.
Supports 10Mbps and 100Mbps data rates.
Uses a single 50MHz reference clock provided by the MAC or the system board.
Provides independent 2-bit wide (di-bit) transmit and receive data paths.
Contains two distinct groups of signals: one for transmission and the other for reception.
A 50 MHz reference clock connected to REFCLK (pin 15).
CONFIG[2:0] (pins 27, 41, 40) set to ‘001’.
27
KSZ8041TL/FTL/MLL
M9999-120909-1.2