MCP3901A0-E/SS Microchip Technology, MCP3901A0-E/SS Datasheet - Page 38
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
MCP3901A0-E/SS
Manufacturer Part Number
MCP3901A0-E/SS
Description
IC ENERGY METER AFE 2CH 20-SSOP
Manufacturer
Microchip Technology
Datasheets
1.MCP3901A0-ISS.pdf
(60 pages)
2.MCP3901A0-ISS.pdf
(30 pages)
3.MCP3901A0-ISS.pdf
(58 pages)
Specifications of MCP3901A0-E/SS
Number Of Bits
24
Number Of Channels
2
Power (watts)
10mW
Voltage - Supply, Analog
4.5 V ~ 5.5 V
Voltage - Supply, Digital
2.7 V ~ 5.5 V
Package / Case
20-SSOP (0.200", 5.30mm Width)
Ic Function
Analog Front End Device IC
Supply Voltage Range
4.5V To 5.5V
Operating Temperature Range
-40°C To +85°C
Digital Ic Case Style
SSOP
No. Of Pins
20
No. Of Channels
2
Input Voltage
2.2 V to 2.6 V
Mounting Style
SMD/SMT
Supply Voltage Max
5.5V
Rohs Compliant
Yes
Interface Type
SPI
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MCP3901A0-E/SS
Manufacturer:
Microchip
Quantity:
1 865
MCP3901
6.9
To signify when channel data is ready for transmission,
the data ready signal is available on the Data Ready pin
(DR) through an active-low pulse at the end of a
channel conversion.
The data ready pin outputs an active-low pulse with a
period that is equal to the DRCLK clock period, and
with a width equal to one DMCLK period.
When not active-low, this pin can either be in high-
impedance (when DR_HIZN = 0) or in a defined logic
high state (when DR_HIZN = 1). This is controlled
through the Configuration registers. This allows
multiple devices to share the same data ready pin (with
a pull-up resistor connected between DR and DV
3-phase, energy meter designs to reduce M. pin count.
A single device on the bus does not require a pull-up
resistor.
After a data ready pulse has occurred, the ADC output
data can be read through SPI communication. Two sets
of latches at the output of the ADC prevent the
communication from outputting corrupted data (see
Section 6.10 “Data Ready Latches and Data Ready
Modes
The CS pin has no effect on the DR pin, which means
even if CS is high, data ready pulses will be provided
(except when the configuration prevents them from
outputting data ready pulses). The DR pin can be used
as an interrupt when connected to an MCU or DSP.
While the RESET pin is low, the DR pin is not active.
DS22192C-page 38
(DRMODE<1:0>)”).
Data Ready Pin (DR)
DD
) in
6.10
To ensure that both channels’ ADC data is present at
the same time for SPI read, regardless of phase delay
settings for either or both channels, there are two sets
of latches in series with both the data ready and the
‘read start’ triggers.
The first set of latches holds each output when the data
is ready and latches both outputs together when
DRMODE<1:0> = 00. When this mode is on, both
ADCs work together and produce one set of available
data after each data ready pulse (that corresponds to
the lagging ADC data ready). The second set of latches
ensures that when reading starts on an ADC output, the
corresponding data is latched so that no data
corruption can occur.
If an ADC read has started, in order to read the
following ADC output, the current reading needs to be
completed (all bits must be read from the ADC Output
Data registers).
6.10.1
There are four modes that control the data ready
pulses
DRMODE<1:0> bits in the STATUS/COM register. For
power metering applications, DRMODE<1:0> = 00 is
recommended (Default mode).
Data Ready Latches and Data
Ready Modes (DRMODE<1:0>)
and
DATA READY PIN (DR) CONTROL
USING DRMODE BITS
these
modes
© 2010 Microchip Technology Inc.
are
set
with
the