MTCBA-C1-EN2-GP-N3 Multi-Tech Systems, MTCBA-C1-EN2-GP-N3 Datasheet - Page 111
![no-image](/images/no-image-200.jpg)
MTCBA-C1-EN2-GP-N3
Manufacturer Part Number
MTCBA-C1-EN2-GP-N3
Description
ROUTER WIRELESS DUAL CDMA
Manufacturer
Multi-Tech Systems
Series
MultiModem® rCellr
Datasheets
1.SF100-G.pdf
(4 pages)
2.MTCBA-C1-N16.pdf
(135 pages)
3.MTCMR-E1.pdf
(16 pages)
4.MTCMR-E1.pdf
(79 pages)
5.MTCMR-E1.pdf
(2 pages)
6.MTCMR-C1-N2.pdf
(2 pages)
Specifications of MTCBA-C1-EN2-GP-N3
Function
Transceiver, CDMA, Router
Modulation Or Protocol
CDMA2000
Frequency
800MHz, 1.9GHz, 1575.42MHz
Applications
Verizon™ Networks (USA)
Interface
RJ-45, RS-232
Sensitivity
-161dB
Voltage - Supply
9 V ~ 32 V
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
881-1063
Configure Antenna Diagnostics +WANTLIM
Description:
Syntax
Values:
Multi-Tech Systems, Inc. CDMA C1 AT Commands Reference Guide (PN S000478C)
Commands (Not for IP and GPS
This command is used to configure the low limit and high limit diagnostic values of the primary
and secondary (diversity or GPS) antenna. The values are compared to the ADC reading from
the antenna diagnostic voltage divider network. The current antenna status (NORMAL, OPEN, or
SHORTED) is derived from comparison to these limits.
The ADC used to read the antenna diagnostic voltage divider network for the primary antenna
may be selected using the AT+WANTADC command.
The secondary antenna has two sets of low/high limits—one for the non-powered state and one
for the powered state. The secondary antenna is powered when the setting of AT+WANT=1. For
hardware revisions 2.1 and later, the non-powered low/high limits of the secondary antenna are
not applicable. Use the +WHWV command to determine the hardware version of your device.
The limit settings are persistent across power cycles.
Command Syntax:
AT+WANTLIM=<action>,<ant>[,<lowlim>,<highlim>[,<poweredLowlim>,<poweredHighlim>]]
<action>
<ant>
<lowlim>
<highlim> The ADC value above which the non-powered antenna is considered to be in an
Command
AT+WANTLIM=?
Note: show parameter ranges
AT+WANTLIM=1,1,30,74
Note: Set primary antenna low and high limits
AT+WANTLIM=2,1
Note: Display primary antenna diagnostic
limits
AT+WANTLIM=1,2,30,74,185,222
Note: Set secondary antenna non-powered
and powered low and high limits
AT+WANTLIM=2,2
Note: Display secondary antenna diagnostic
limits
AT+WANTLIM=2,1,53,33
Chapter 19 – Antenna
1
2
1
2
Set values
Display values
Primary antenna
Secondary antenna
The ADC value below which the non-powered antenna is considered to be in a
shorted condition. Possible values are 0-255. Default is 0. This value is ignored for
the secondary antenna of hardware versions 2.1 and later.
open condition. Possible values are 0-255. Default is 255. This value is ignored for
the secondary antenna of hardware versions 2.1 and later.
Builds)
Possible Responses
+WANTLIM: (1-2),(1-2),(0-255),(0-255),(0-
255),(0-255)
OK
OK
+WANTLIM: 1,30,74
OK
OK
+WANTLIM: 2,30,74,185,222
OK
ERROR
Note: Low limit must be less than or equal to
high limit
Chapter 19 – Antenna Commands
111