MTCBA-C1-EN2-GP-N3 Multi-Tech Systems, MTCBA-C1-EN2-GP-N3 Datasheet - Page 49
![no-image](/images/no-image-200.jpg)
MTCBA-C1-EN2-GP-N3
Manufacturer Part Number
MTCBA-C1-EN2-GP-N3
Description
ROUTER WIRELESS DUAL CDMA
Manufacturer
Multi-Tech Systems
Series
MultiModem® rCellr
Datasheets
1.SF100-G.pdf
(4 pages)
2.MTCBA-C1-N16.pdf
(135 pages)
3.MTCMR-E1.pdf
(16 pages)
4.MTCMR-E1.pdf
(79 pages)
5.MTCMR-E1.pdf
(2 pages)
6.MTCMR-C1-N2.pdf
(2 pages)
Specifications of MTCBA-C1-EN2-GP-N3
Function
Transceiver, CDMA, Router
Modulation Or Protocol
CDMA2000
Frequency
800MHz, 1.9GHz, 1575.42MHz
Applications
Verizon™ Networks (USA)
Interface
RJ-45, RS-232
Sensitivity
-161dB
Voltage - Supply
9 V ~ 32 V
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
881-1063
Set Uniform Out-Of-Service Values +WTUOOS
Description:
Syntax:
Values:
Band Preference +WBND
Description:
Syntax:
Values:
Multi-Tech Systems, Inc. CDMA C1 AT Commands Reference Guide (PN S000478C)
This command is used to update the scan and sleep durations for the Uniform Out-of-Service
scanning algorithm. The settings are saved in non-volatile memory. The scan duration and sleep
duration are specified in seconds with values between 1 second and 32767 seconds.
Command Syntax: AT+WTUOOS=[< scanval >], [<sleepval >]
Read Result:
< scanval >
< sleepval >
The Band Preference of a CDMA modem governs the basic system acquisition behavior of the
PRL (Preferring Roaming List). It’s important to note that the PRL takes precedence over band
preference when guiding the phone to a band. The PRL must allow a particular band first, before
the band preference can take effect. In other words, a band preference change is simply a
request; the PRL decides whether or not to allow it. If the setting is accepted by the MS, the value
will be written to non-volatile RAM and persist after a power-cycle.
The behavior of Cellular A and cellular B has changed slightly from previous Wavecom
definitions. Cellular A now means cellular A is preferred, and cellular B means cellular B is
preferred. As an example: If the device is set to cellular A, the modem will look for service on the
A side first. If service cannot be found, the modem will then check the B side for service before
reporting no service.
Note:
Command syntax: AT+WBND=<band>,<persist>
<band>
<persist>
Command
AT+WTUOOS=1,2
AT+WTUOOS?
Note: Current values
AT+WTUOOS=?
Command
AT+WBND?
Note: Ask for current Band Preference
AT+WBND=?
AT+WBND=0
Note: Allow Any Band
0
1
2
3
4
0
1
1 – 32767 Uniform out of service scan value in seconds. (Default = 4 seconds)
1 – 32767 Uniform out of service sleep value in seconds. (Default = 36 seconds)
Any
PCS
Cellular A or B
Cellular A
Cellular B
Do not save to NV
Save to NV (default)
The command may not be available in all software variations due to carrier requirements.
+WTUOOS: <scanval>,<sleepval>
Possible Responses
OK
Note: Command valid
+WTUOOS: 1,2
OK
Note: Command valid
+WTUOOS: (1-32767),(1-32767)
OK
Note: Test Command
Possible Responses
+WBND: 0
OK
Note: Any
+WBND: (0-4),(0-1)
OK
Note: Any, PCS, Cell, Cell A, Cell B
OK
Chapter 10 – Network Service Commands
49