KMA200,115 NXP Semiconductors, KMA200,115 Datasheet - Page 23

• Manufacturer Part Number: KMA200,115
• Description: IC SENSOR PROG ANGLE SOT637
• Manufacturer: NXP Semiconductors

Specifications of KMA200,115

• Position - Sensing: 180°
• Sensor Type: Angular - Magnetoresistive
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 160°C
• Package / Case: SOT-637
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Supply Current: 12 mA
• Maximum Operating Temperature: + 160 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: Through Hole
• Product: Programmable Angle Sensor
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 568-4286-2; 934056510115; KMA200 T/R

NXP Semiconductors
KMA200_7
Product data sheet
13.4 Write RAM (0nh), read RAM (1nh)
13.5 Calculate CRC-16 and program EEPROM (30h)
Address B: storage the assembly lot no. (maximum 65535)
To write data to the RAM the command byte 0nh (n is the address of the data) followed by
the 16-bit data has to be send. To read data from the RAM, the command byte 1nh has to
be send. If CS is activated again, the RAM contents at the specified address is clocked
out. Note that at power-on addresses 00h to 0Fh are read from the EEPROM into the
RAM.
To program the EEPROM, the configuration data has to be written to the RAM addresses
00h to 0Eh. Afterwards, the command byte 30h has to be sent and the EEPROM
programming voltage has to be applied at the V
CRC-16 check sum and writes the RAM constants at addresses 00h to 0Fh to the
EEPROM. This command is only executed when the EP bit in the control information word
is logic 0 on power-on. If the EP bit is logic 1, this command is ignored.
Table 9.
Address
0
1
2
3
4
5
6
7
8
9
A
B
C
EEPROM content
Name
sensor_offset_1
sensor_offset_2
zero_angle
angular_range
temp_vref, temp_offs
T
ctrl1
ctrl2
V
id1
id2
anom, tc_anom
shut(res)
thresh
(CL)l
, V
(CL)u
, T
warn(res)
Rev. 07 — 18 July 2008
Description
dependent of individual production calibration results
dependent of individual production calibration results
mechanical 0 position relative to the zero point of the
sensor output; used for zero-angle calibration
default value: 0000h (0 )
definition of the angular input range that is mapped to the
whole analog output signal range
default value: 0000h (180 )
threshold for programmable output in mode 3
default value: internal CRC of the addresses 0, 1, 5, C, D
and E
dependent of individual production calibration results
temperature warning and temperature shutdown level; used
for temperature supervision default value: FAF8h
(temperature shutdown at 200 C, warning at 198 C)
control information word 1; used for selection of various
operating modes default value: 4046h (output mode
standard + mode 1)
control information word 2; configures the diagnostic
functions default value: 0704h (temperature supervision is
on; input stage diagnosis is on; output stage diagnosis is off)
clamping voltage levels of analog outputs
default value: 00FFh (clamping level LOW at 5 %V
clamping level HIGH at 95 %V
sensor identifier 1; this data is not evaluated by the KMA200
and is used for sensor identification
sensor identifier 2; this data is not evaluated by the KMA200
and is used for sensor identification
dependent of individual production calibration results
DD
pin. The KMA200 calculates the
Programmable angle sensor
DD
)
© NXP B.V. 2008. All rights reserved.
KMA200
DD
,
23 of 32