196 TPI (Test Products Int), 196 Datasheet
196
Specifications of 196
196TPI
290-1425
TPI 196
TPI196
Available stocks
196 Summary of contents
Page 1
Specifications % Basic DCV Accuracy ±0.05 Function Range Resolution DCV 50mV 0.001mV 500mV 0.01mV 5V 0.0001V 50V 0.001V 500V 0.01V 1000V 0.1V ACV 5V 0.0001V 50V 0.001V 500V 0.01V 750V 0.1V DCA/ACA 500µA 0.01µA 5000µA 0.1µA 50mA 0.001mA 500mA ...
Page 2
TABLE OF CONTENTS A. INTRODUCTION 1. Congratulations ··············· 2. Product Description ············ Declaration of Conformity B. SAFETY CONSIDERATIONS ········· C. TECHNICAL DATA 1. Features and Benefits ··········· 2. Product Applications ··········· 3. Specifications ················ D. MEASUREMENT TECHNIQUES 1. ...
Page 3
A. INTRODUCTION INTRODUCTION 1. Congratulations!! Thank you for purchasing a TPI Digital Multimeter. The Triple Display is an innovative new concept in DMM design. The unique display enables you to view more than one event at a time. This eliminates ...
Page 4
B. SAFETY CONSIDERATIONS WARNING! : Please follow manufacturers test procedures whenever possible. Do not attempt to measure unknown voltages or components until a complete understanding of the circuit is obtained. GENERAL GUIDELINES ALWAYS • Test the meter before using to ...
Page 5
C. TECHNICAL DATA 1. Features and benefits Safety Meets CE and IEC 1010 requirements. UL Listed to U.S. and Canadian Safety Standards. True RMS Needed to accurately measure non- sinusoidal AC voltage and current waveforms found on many controls and ...
Page 6
Specifications IEC 1010 Over Voltage: (190, 192) CAT II-1000VDC, 750VAC CATIII-600V Pollution Degree 2 EC 1010 Over Voltage: (194) CATIII-1000V CATIV-600V Pollution Degree 2 ※ INSTALLATION I·II·III INSTALLATION CATEGORY(OVERVOLTAGE CATEGORY Signal level, special equipment or parts of ...
Page 7
Specifications (cont.) c. DCA Range Resolution Accuracy 500uA 0.01uA +/-0.5% of reading, 5000uA 0.1uA +/- 5digits 5000uA 0.1uA 50mA 0.001mA 500mA 0.01mA +/-0.75% of reading, Fuse(fast blow) 5A 0.0001A +/- 5digits 10A 0.001A d. ACA Range Resolution Accuracy 500uA ...
Page 8
Specifications (cont.) j. frequency Range Resolution Accuracy 50Hz 0.001Hz 500Hz 0.01Hz +/-0.05% of reading, 600V 5Khz 0.0001Khz +/- 5digits 50Khz 0.001Khz 500Khz 0.01Khz k. Adaptor Model A301(Temp Adaptor C/F) 1mV/C, 1mV/F 0000.0 C/F A254(Current Adaptor 10/60A) ...
Page 9
Selects the Inductance function Selects the Frequency function Selects the DC uA function (Push ORANGE button to activate AC uA. Selects the DC mA function (Push ORANGE button to activate AC mA.) Selects the DC A function (Push ORANGE button ...
Page 10
Step by step procedure a. Measuring DC Volts CAUTION Do not attempt to make a voltage measurement if a test lead is plugged in the input jack. Instrument damage and/or personal injury may result. WARNING! Do ...
Page 11
Measuring AC Volts CAUTION Do not attempt to make a voltage measurement if a test lead is plugged in the A or umA input jack. Instrument damage and/or personal injury may result. WARNING! Do not attempt to make a ...
Page 12
Application Notes When measuring the DC current of a flame controller, follow the steps under “Measurement Procedure” above and then proceed with the following: • Set up the meter for making a µA measurement. • Connect the meter to the ...
Page 13
Measuring Resistance WARNING! Do not attempt to make resistance measurements with circuit energized. For best results, remove the resistor completely from the circuit before attempting to measure it. NOTE: To make accurate low ohm measurements, short the ends of ...
Page 14
Continuity Buzzer WARNING! Do not attempt to make continuity measurements with circuit energized. Instrument set-up: I FUNCTION BLACK TEST LEAD COM Measurement Procedure: 1. Disconnect power to circuit to be measured. COM 2. Plug black test lead into the ...
Page 15
Measuring Inductance (Only 192) FUNCTION BLACK RED TEST LEAD TEST LEAD mH COM umAmH Measurement Procedure: 1. Disconnect power to circuit to be measured. COM 2. Plug black test lead into the 3. Plug red test lead into the ...
Page 16
Record Mode The record mode saves minimum (MIN) and maximum (MAX) values measured for a series of readings. The main part of the LCD displays the actual reading, the MAX value is constantly displayed on the lower left hand ...
Page 17
Relative % Mode The Relative % mode takes the actual reading on the main display and compares reference value programmed by the user on the right hand sub-display. The left hand sub- display will show the ...
Page 18
Push button code Push key Code RANGE RANGE AUTO/ RANGE MANUAL REC REC ON/ REC AVG/ REC OFF REL REL ON ref2/ REL OFF COMP COMP ON ref1 ref2/ COMP OFF HOLD HOLD ON/ HOLD OFF ) ref1 is the ...
Page 19
E. ACCESSORIES Standard Accessories 9 Volt Alkaline Battery Fuse 0.5A Fuse 0.44A(Only194) Fuse 10A Fuse 11A(Only194) Test lead Rubber boot Optional Accessories Accessories Demonstration Software Deluxe Test lead set IEC 1010 Deluxe test lead kit Temperature Adaptor Current Adaptor 10/60A ...
Page 20
G. TROUBLE SHOOTING GUIDE Problem Probable Causes Does not power up • Dead or defective battery • Broken wire from battery snap to PCB Won’t display current readings • Open fuse • Open test lead • Improperly connected to circuit ...