FLUKE-113 Fluke Electronics, FLUKE-113 Datasheet
![no-image](/images/no-image-200.jpg)
FLUKE-113
Specifications of FLUKE-113
FLUKE-113 Summary of contents
Page 1
... V dc. These voltages pose a shock hazard. • Disconnect circuit power and discharge all high-voltage capacitors before testing resistance, continuity, diodes, or capacitance. PN 3083192 December 2007 ©2007 Fluke Corporation. All rights reserved. Specifications subject to change without notice. Printed in China Electrical Multimeter Instruction Sheet ® 113 ...
Page 2
Do not use the Meter around explosive gas, vapor or in wet environments. • When using test leads or probes, keep your fingers behind the finger guards. • Only use test leads that have the same voltage, category, and ...
Page 3
... Do not dispose of this product as unsorted municipal waste Fluke’s website for recycle information. Terminals 1 No. A Common (return) terminal for all measurements. B Input terminal for all measurements. ...
Page 4
Automatic Range Selection The meter defaults to autoranging when turned on. To return to autoranging while in the manual range mode, press qfor 1 second. Manual Range Selection ( See each function in this instruction sheet for available ranges. k ...
Page 5
Battery Saver If the Meter is ON, but inactive and not connected to voltage for more than 20 minutes, the display goes blank to preserve battery life. To resume operation, press any button or turn the rotary switch. To disable ...
Page 6
Power-Up Options To select a Power-Up Option, hold down the button indicated in the following table while turning the Meter from off to the function. Power-Up Options are canceled when you turn the Meter off and when sleep mode is ...
Page 7
W k CHEK voltage greater than about present across the inputs when the meter is set to k CHEK, the meter switches automatically voltage mode and displays the ...
Page 8
Diode Test G Turn off circuit power before testing. For best results, diodes should be measured out of circuit. Also refer to k CHEK Good Diode Good Diode Forward Bias Bad Diode Bad Diode Open . Good Diode Single Beep ...
Page 9
Continuity s Turn off circuit power before testing. Continuity Capture Turn off circuit power before testing. Open MIN MAX Short fda05.eps fda06.eps ...
Page 10
Short to Open Captures transitions longer than 500 μs (1/2000 Transitions after the first transition cause the Meter to beep, but the display does not change. To reset the display to the current condition, press p. To exit, press pfor ...
Page 11
Resistance e Turn off circuit power before testing. Capacitance E Turn off circuit power, then disconnect and discharge the capacitor before measuring capacitance. Note correct probe polarity for polarized capacitors. 600 6 60 RANGE RANGE fda07.eps fda08.eps ...
Page 12
MIN MAX (Records the lowest, highest, and calculated average measurements.) Autoranging, and Battery Saver™ are disabled. Put the meter in the proper range before entering MIN MAX. When a new minimum or maximum is recorded, the meter beeps. Enter MIN ...
Page 13
... This meter should be serviced only by a qualified service technician. To locate an authorized service center, call: USA: 1-888-99-FLUKE (1-888-993-5853) Canada: 1-800-36-FLUKE (1-800-363-5853) Europe: +31 402-675-200 Japan: +81-3-3434-0181 Singapore: +65-738-5655 Anywhere in the world: +1-425-446-5500 Or, visit Fluke's Web site at www.fluke.com. p for 2 seconds while eeo11f.eps PN 855705 PN 3083192 ...
Page 14
Specifications Accuracy is specified for 1 year after calibration, at operating temperatures of 18 ° °C, with relative humidity are given as follows: Specifications are subject to change without notice. ±([% of ...
Page 15
Maximum Voltage Between any Terminal and Earth Ground: Display: Operating Temperature: Storage Temperature: Temperature Coefficient: Operating Altitude: Storage Altitude: Relative Humidity: Battery Type: Battery Life: Shock: Vibration: Size ( L): Weight: Safety: EMI Regulations: Certifications: 600 V ...
Page 16
Function k Chek Common Mode Rejection Ratio (1 kΩ Unbalanced) k Chek Open Circuit Test Voltage Ω R Ω R MIN MAX Recording Accuracy and Response Time Specified accuracy of the measurement function ±40 counts in kChek for changes >500 ...
Page 17
... LIMITED WARRANTY & LIMITATION OF LIABILITY This Fluke product will be free from defects in material and workmanship for three years from the date of purchase. This warranty does not cover fuses, disposable batteries, or damage from accident, neglect, misuse, alteration, contamination, or abnormal conditions of operation or handling. Resellers are not authorized to extend any other warranty on Fluke’ ...