A22EL-M-24A-02 Omron, A22EL-M-24A-02 Datasheet - Page 18
![IL ESTOP 40mm 24V DPST-NC](/photos/17/71/177138/a22ef_sml.jpg)
A22EL-M-24A-02
Manufacturer Part Number
A22EL-M-24A-02
Description
IL ESTOP 40mm 24V DPST-NC
Manufacturer
Omron
Series
A22r
Type
Emergency Stop, Illuminatedr
Specifications of A22EL-M-24A-02
Illumination Color
Red
Circuit
DPST-NC
Switch Function
On-Off
Contact Rating @ Voltage
10A @ 110VAC
Actuator Type
Mushroom Button
Illumination Type, Color
LED, Red
Illumination Voltage (nominal)
24 VAC/DC
Mounting Type
Panel Mount
Termination Style
Screw Terminal
Contact Form
DPST - NC
Contact Rating
10 Amps at 110 Volts
Actuator
Round, Medium
Mounting Style
Through Hole
Illumination
Illuminated
Body Shape
Square
Dielectric Strength
2500 Volts
Features
Easy mounting and removal of switch unit
Insulation Resistance
100 MOhms
Mounting Angle
Straight
Water / Moisture Rating
IP65
Contact Configuration
DPST-NC
Switch Operation
Pushlock Turn Reset
Contact Voltage Ac Nom
440V
Contact Voltage Dc Nom
380V
Contact Current Max
24A
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
A22ELM24A02
Control Box (Enclosure)
Installing/Removing the Switch Blocks
The Standard-size Legend Plate Frame can be mounted. Mount the Frame as
shown in the following diagram. Mount the Switch in the same way as for an
ordinary panel.
1. Insert the connector into the cable port hole in the Box and secure with the fixing nut inside the box.
2. Open a hole in the thin rubber section of the rubber ring.
3. Pass the tightening cap through the cable, insert the cable into the connector, and tighten the hexagonal nut to secure the cable.
• Hook the small protrusion on the Mounting Latch
into the groove on the other side of the lever, then
push up the Switch Block in the direction indicated
by the arrow in the figure below.
Mounting
Latch
(1) Installing the Switch Blocks
(1) Mounting the Switch
http://www.ia.omron.com/
Switch block
Lock nut
Protrusion
Inside
Box
Lever
Snap-in Legend Plate
Outside
• Insert a screwdriver between the Mounting Latch
Rubber washer
and the Switch Block, then push down the
screwdriver in the direction indicated by the arrow
in the following figure.
Use either of the following screwdrivers.
Flat-head screwdriver
Phillips screwdriver
(2) Removing the Switch Blocks
(3) Securing the Connector Cable
Connector
3 to 6 mm dia.
3 to 6 mm
Tightening
Place the tip of a screwdriver on the surface where the cable port hole is to be
created with the cover attached and strike the screwdriver to punch a hole.
Attempts to punch a hole on the other side of the case will damage the Box.
Screwdriver
(c)Copyright OMRON Corporation 2007 All Rights Reserved.
Cable
(2) Creating a Cable Port Hole
• Loosen the terminal screw from the Switch
Screw
Unit until it completely comes off the groove,
insert a screwdriver as shown in the following
figure, then push up the washer in the
direction indicated by the arrow to temporarily
secure it. Now, a round crimp terminal can be
connected. After inserting the terminal,
tighten the screws to complete wiring.
Washer
7 to 9 dia.
9 to 11 dia.
Cable diameter
Wiring
A22Z-3500-1
A22Z-3500-2
Connector
Screwdriver
A22E
18