A22EL-M-24A-02 Omron, A22EL-M-24A-02 Datasheet - Page 19
![IL ESTOP 40mm 24V DPST-NC](/photos/17/71/177138/a22ef_sml.jpg)
A22EL-M-24A-02
Manufacturer Part Number
A22EL-M-24A-02
Description
IL ESTOP 40mm 24V DPST-NC
Manufacturer
Omron
Series
A22r
Type
Emergency Stop, Illuminatedr
Specifications of A22EL-M-24A-02
Illumination Color
Red
Circuit
DPST-NC
Switch Function
On-Off
Contact Rating @ Voltage
10A @ 110VAC
Actuator Type
Mushroom Button
Illumination Type, Color
LED, Red
Illumination Voltage (nominal)
24 VAC/DC
Mounting Type
Panel Mount
Termination Style
Screw Terminal
Contact Form
DPST - NC
Contact Rating
10 Amps at 110 Volts
Actuator
Round, Medium
Mounting Style
Through Hole
Illumination
Illuminated
Body Shape
Square
Dielectric Strength
2500 Volts
Features
Easy mounting and removal of switch unit
Insulation Resistance
100 MOhms
Mounting Angle
Straight
Water / Moisture Rating
IP65
Contact Configuration
DPST-NC
Switch Operation
Pushlock Turn Reset
Contact Voltage Ac Nom
440V
Contact Voltage Dc Nom
380V
Contact Current Max
24A
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
A22ELM24A02
Safety Precautions
Be sure to read the precautions for all pushbutton switches in the Pushbutton Switches Group Catalog (Cat. No. X018).
■ Precautions for Correct Use
Mounting
• Always make sure that the power is turned OFF before wiring the
• Do not tighten the mounting ring more than necessary using tools
• Recommended panel thickness: 1 to 5 mm.
Wiring
• When DC-specific LEDs are used, wire the Switch so that the X1
• Terminal screws must be Phillips or slotted M3.5 screws with a
• The tightening torque is 1.08 to 1.27 N·m.
• Single wires, stranded wires, and crimp terminals can be
• Applicable Wiring Materials:
• After wiring the Switch, maintain an appropriate clearance and
Operating Environment
• The IP65 model is designed with a protective structure so that it will
LEDs
• The LED current-limiting resistor is built-in, so internal resistance is
• If commercially available LEDs are used, select the ones that meet
Cat. No. A119-E1-06
Do not apply a voltage exceeding the rated voltage across the
incandescent lamp terminals.
The lamp may be destroyed and the operation unit may fly out.
Switch. Also, do not touch the terminals or other current-carrying
ports while power is being supplied. Electric shock may occur.
such as pointed-nose pliers. Doing so will damage the mounting
ring. The tightening torque is 0.98 to 1.96 N·m.
terminal is positive.
square washer.
connected to the Switch.
Twisted strands: 2 mm
Solid wire: 1.6 mm dia.
Naked Crimp Terminals
creepage distance.
not sustain damage if it is subjected to water from any direction to
the front of the panel.
not required.
the following conditions:
Base: BA9S/13@
Overall length: 26 mm max.
Power consumption: 2.6 W max.
Crimp Terminals with
Insulating Sheaths
http://www.ia.omron.com/
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
2
max.
!CAUTION
20.2 mm max.
16.0 mm max.
In the interest of product improvement, specifications are subject to change without notice.
8 mm max.
8 mm max.
20.2 mm max.
16.0 mm max.
8 mm dia. max.
8 mm dia. max.
Using the Microload
• Contact failure may occur if a Switch designed for a standard load
Others
• If the panel is to be coated, make sure that the panel meets the
• Due to the structure of the Switch, severe shock or vibration may
is used to switch a microload. Use Switches within the application
ranges shown in the following graph. Even within the application
range, insert a contact protection circuit, if necessary, to prevent
the reduction of life expectancy due to extreme wear on the
contacts caused by loads where inrush current occurs when the
contact is opened and closed.
The minimum applicable load is the N-level reference value. This
value indicates the malfunction reference level for the reliability
level of 60% ( 60) (conforming to JIS C5003).
The equation,
malfunction rate is less than 1/2,000,000 with a reliability level of
60%.
specified dimensions after coating.
cause malfunctions or damage to the Switch. Also, most Switches
are made from resin and will be damaged if they come into contact
with sharp objects. Particularly scratches on the Operation Unit
may create visual and operational obtrusions. Handle the Switches
with care, and do not throw or drop them.
(c)Copyright OMRON Corporation 2007 All Rights Reserved.
60 = 0.5 x 10
Hammer
30
12
24
5
0
0.1
0.16 mA
Invalid
area
1 mA
Screwdriver
1
1.6 mA
Microload area
6
/time indicates that the estimated
10 mA
10
Do not allow the
Switch to drop and hit
the floor.
Do not place or drop
heavy objects on the
Switch.
Do not operate the
Switch with hard or
sharp objects.
Current (mA)
100 mA
100
Standard
load area
Area of
use
1,000
A22E
19