NS5-MQ10B-V2 Omron, NS5-MQ10B-V2 Datasheet - Page 14

• Manufacturer Part Number: NS5-MQ10B-V2
• Description: 5 Mono Tchsrn,Serial+USB,Bk 60
• Manufacturer: Omron

Specifications of NS5-MQ10B-V2

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Precautions for Safe Use
12
1. When unpacking the Units, check carefully for any external scratches or other damage.
2. The PT must be installed in a control panel.
3. The mounting panel must be between 1.6 and 4.8 mm thick. Tighten the Mounting
4. Do not let metal particles enter the Units when preparing the panel.
5. Do not connect an AC power supply to the DC power input terminals.
6. Use a DC power supply with minimal voltage fluctuation that provides a stable output even
7. Do not perform a dielectric voltage test.
8. Use a twisted-pair cable with a cross-sectional area of at least 2 mm
9. Ground the Unit correctly to prevent operational errors caused by noise.
10. Do not touch the surface of the circuit board or the components mounted on it with your
11. Confirm that the current capacity of the connected device is 250 mA or less before using
12. Turn OFF the power supply before connecting or disconnecting cables.
13. Always tighten the connector screws after connecting communications cables.
14. The maximum tensile load for cables is 30 N. Do not apply loads greater than this.
15. Confirm the safety of the system before turning ON or OFF the power supply or before
16. The whole system may stop depending on how the power supply is turned ON or OFF.
17. After changing the settings of the DIP switch, always turn the power supply OFF and ON
18. Do not perform the following operations while the Memory Card is being accessed:
19. To ensure system safety, incorporate a program that periodically calls PT operation bits
20. Start actual system application only after sufficiently checking screen data, macros, and
21. Do not press a touch switch with a force greater than 30 N.
22. Do not operate a touch switch using a screwdriver or other tool.
23. Confirm the safety of the system before pressing a touch switch.
24. Do not press touch switches consecutively without pausing in between. If touch switches
25. Do not accidentally press touch switches when the backlight is not lit or when the display
Also, shake the Units gently and check for any abnormal sound.
Brackets evenly to a torque of between 0.5 and 0.6 N⋅m to maintain water and dust
resistance. Make sure the panel is not dirty or warped and that it is strong enough to hold
the Units.
if the power supply input is interrupted for 10 ms. The DC power supply must also have
reinforced or double insulation.
Rated power supply voltage: 24 VDC (Allowable range: 20.4 to 27.6 VDC)
Capacity:
power terminals and always use M3.5 crimp terminals. Tighten the terminal screws to a
torque of 0.8 N⋅m. Make sure the screws are properly tightened.
bare hands. Discharge any static electricity from your body before handling the board.
the 5-V power supply from pin 6 of the RS-232C connector. The 5-V output from the PT is
250 mA max. at 5 V ±5%.
pressing the reset button.
Turn ON or OFF the power supply according to the specified procedure.
or reset the PT.
from the host side to check that the PT is properly operating.
the operation of the program in the host.
are pressed consecutively at high speed, the PT may not be able to detect the inputs.
Confirm that the PT has detected the input of a touch switch before pressing any other
touch switch.
does not appear. Confirm the safety of the system before pressing touch switches.
• Turning OFF the power supply to the PT
• Pressing the PT’s reset switch
• Removing the Memory Card
NS15: 45 W min.
NS12, NS10, or NS8: 25 W min.
NS5: 15 W min.
2
to connect to the