A165E-S-01 Omron, A165E-S-01 Datasheet - Page 10

• Manufacturer Part Number: A165E-S-01
• Description: E-stop,non-lighted,1NC,30diamt
• Manufacturer: Omron
• Series: A16r
• Type: Emergency Stopr

Specifications of A165E-S-01

• Circuit: SPST-NC
• Switch Function: On-Off
• Contact Rating @ Voltage: 5A @ 125VAC
• Actuator Type: Round Button
• Mounting Type: Panel Mount
• Termination Style: Solder, Quick Connect - .110" (2.8mm)
• Control Type: Emergency Stop
• Contact Form: SPST - NC
• Contact Rating: 5 Amps at 125 VoltsAC
• Illuminated: N
• Contact Configuration: SPST-NC
• Switch Operation: Pushlock Turn Reset
• Contact Voltage Ac Nom: 250V
• Contact Voltage Dc Nom: 30V
• Contact Current Max: 5A
• Actuator Style: Round
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Illumination Type, Color: -
• Illumination Voltage (nominal): -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: A165ES01; Z1427

Safety Precautions
Be sure to read the precautions for all pushbutton switches in the Pushbutton Switches Group Catalog (Cat. No. X018).
■ Precautions for Correct Use
Mounting
• Always make sure that the power is turned OFF before mounting,
• The tightening torque is 0.29 to 0.49 N·m.
Wiring
• Be sure to use electrical wires that are a size appropriate for the
• Use non-corrosive resin fluid as the flux.
• Make sure that the electric cord is wired so that it does not touch
• After wiring the Switch, maintain an appropriate clearance and
Operating Environment
• The IP65 model is designed with a degree of protection so that it
Using the Microload
• Insert a contact protection circuit, if necessary, to prevent the
• The A165E-@U (one-piece construction) allows both a standard
• The minimum applicable load is the N-level reference value. This
Cat. No. A120-E1-06
removing, or wiring the Switch, or performing maintenance.
Electrical shock or fire may result if the power is not turned OFF.
applied voltage and carry current. Perform soldering according to
the conditions given below. If the soldering is not properly
performed, abnormal heating may result, possibly resulting in fire.
1. Hand soldering: 30 W, within 5 s
2. Dip soldering: 240 C, within 3 s
Wait for one minute after soldering before exerting any external
force on the solder.
the Unit. If the electric cord will touch the Unit, then electric wires
with a heat resistance of 100 C min. must be used.
creepage distance.
will not sustain damage if it is subjected to water from any direction
to the front of the panel.
reduction of life expectancy due to extreme wear on the contacts
caused by loads where inrush current occurs when the contact is
opened and closed.
load (125 V at 1 A, 250 V at 0.5 A) and a microload. If a standard
load is applied, however, the microload area cannot be used. If the
microload area is used with a standard load, the contact surface
will become rough, and the opening and closing of the contact for a
microload may become unreliable.
value indicates the malfunction reference level for the reliability
level of 60% ( 60) (conforming to JIS C5003).
The equation,
malfunction rate is less than 1/2,000,000 with a reliability level of
60%.
60 = 0.5 x 10
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
0.15 mA
Invalid
area
http://www.ia.omron.com/
1 mA
6
/time indicates that the estimated
In the interest of product improvement, specifications are subject to change without notice.
Area of use
Current (mA)
LEDs
• The LED current-limiting resistor is built-in, so external resistance is
Operating Torque
• Do not exceed an operating torque of 0.49 N·m in the direction of
• Do not pull the operating button or apply excessive force to any
Others
• The oil-resistant IP65 uses NBR rubber and is resistant to general
• If the panel is to be coated, make sure that the panel meets the
• Due to the structure of the Switch, severe shock or vibration may
24 VDC
not required.
rotation.
side of the button. Otherwise it may be damaged.
cutting oil and cooling oil. Some special oils cannot be used with
the oil-resistant IP65, however, so contact your OMRON
representative for details.
specified dimensions after coating.
cause malfunctions or damage to the Switch. Also, most Switches
are made from resin and will be damaged if they come into contact
with sharp objects. Particularly scratches on the Operation Unit
may create visual and operational obtrusions. Handle the Switches
with care, and do not throw or drop them.
(c)Copyright OMRON Corporation 2007 All Rights Reserved.
Rated voltage
Hammer
Screwdriver
2000
Internal limiting resistor
Do not operate the
Switch with hard or
sharp objects.
Do not place or drop
heavy objects on the
Switch.
Do not allow the
Switch to drop and hit
the floor.
A165E
10