DCN4-BR4D Omron, DCN4-BR4D Datasheet - Page 62
DCN4-BR4D
Manufacturer Part Number
DCN4-BR4D
Description
Thin Cable-Flat Cable Conv Con
Manufacturer
Omron
Datasheet
1.XW4B-05C4-TF-D.pdf
(166 pages)
Specifications of DCN4-BR4D
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 62 of 166
- Download datasheet (4Mb)
Checking the Installation
of Terminating Resistors
2-2-8
2-2-9
Network Configuration
Using Crimp Terminals
Sharing the Communications and Internal Circuit Power Supply
Note Do not test the resistance while the network is operating. Errors will occur in
If communications errors occur when setting up the system, it is possible to
check whether or not the Terminating Resistors are connected properly. Turn
OFF the network power supply and use a multimeter to test the resistance
between any node’s CAN H signal wire (white) and CAN L signal wire (blue).
the communications data and could cause unexpected problems.
We strongly recommend the use of crimp terminals (solderless pin terminals)
on the wires that connect to the communications cable connectors. The fol-
lowing problems may occur if crimp terminals are not used.
1. A stray wire strand may contact the adjacent terminal and cause a short.
2. The cable may pull out of the connector.
3. The contact between the wire and connector may be poor.
Refer to 2-4 Wiring Methods for information on recommended crimp termi-
nals.
To avoid noise problems, it is generally recommended to provide separate
communications and internal circuit power supplies, but the same power sup-
ply can be used for both purposes if necessary.
When a power supply is shared for the communications and internal circuit
power supplies, wire the network as shown in configuration A. Do not use con-
figuration B because it will generate more noise than configuration A.
• A normal resistance reading is 50 to 70 Ω .
• If the resistance is greater than 70 Ω , there may be a broken signal line
• If the resistance is less than 50 Ω , there may be too many Terminating
in the network or one or both Terminating Resistors may be missing.
A reading of about 100 Ω indicates that one Terminating Resistor is
missing.
A reading of about 300 Ω or higher indicates that both Terminating Re-
sistors are missing.
Resistors (3 or more) in the network.
White (CAN H)
Multimeter
Ω
Blue (CAN L)
Use a multimeter to
measure the resistance
between the signal wires.
Section 2-2
41
Related parts for DCN4-BR4D
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Std. Flat Cbl Branch Line Pres
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
Multi-Wiring Connector
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
Terminal Block Adaptor
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
Std. Flat Cbl Conn Terminating
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
Std. Flat Cbl Trunk Line Press
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
Cabl PwrSupTrmBlk W/ TrmResist
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DeviceNet Flat Cable Connector
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
NonUL Multidrop Flat Connector
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: