XS2R-D526-S003 Omron, XS2R-D526-S003 Datasheet - Page 7

• Manufacturer Part Number: XS2R-D526-S003
• Description: F3W-D Y PLUG
• Manufacturer: Omron

Specifications of XS2R-D526-S003

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

F3W-D
Setting Method
NPN Open-collector Output Models
DIP Switch 1 Mode Switching
Emitters
*1. DIP Switch 1 Picking Display Mode Setting
*2. The flashing speed can be changed in picking display mode (all flashing,
*3. This setting is supported for F3W-D052@P-L Emitters only.
*4. Mutual Interference Prevention Function:
Models with Direct UNI-WIRE Connection
Setting Addresses
(1) Set the picking instruction input address using DIP switch 2
(2) Set the control output addresses using DIP switch 3 on the
Transmission Status
The transmission indicator indicates the status of
bus transmission as follows:
Only one picking indicator flashing also indicates a transmission error.
• The total number of switch addresses set to ON
• Make sure that the addresses of the picking
1
2
3
4
5
6
switch 1
determines the set address (e.g., address 22 in
the diagram at right).
instruction inputs of the Emitter and the
Receiver that are used as a set are the same.
Flashing:
ON or OFF: Transmission error
elevator-like lighting, or accordion-like lighting) or in external picking display
mode. The flashing speed varies with each display mode.
The frequency selector is used to switch the emitting frequency between A
and B. Making the emitting frequencies of two Sensors different helps
prevent malfunction caused by mutual interference.
on the Emitter and Receiver.
Receiver.
DIP
• Elevator-like Lighting Mode
• Accordion-like Lighting Mode
switch 1
LED1
LED2
LED3
LED4
LED5
LED6
LED1
LED2
LED3
LED4
LED5
LED6
1
2
3
4
5
6
DIP
1 Flash Pattern
2
3
4
5 Not used.
6 Frequency Setting *4
(picking display mode setting)
Flash Time *2
(picking indicator flashing speed
setting)
External Flash Pattern
(external picking display mode
setting) *3
OFF
OFF
Normal operation
SW
1-1
ON
ON
http://www.ia.omron.com/
Function
OFF
OFF
SW
1-2
ON
ON
Changes in Indicators
Changes in Indicators
All lighting
(All six indicators light.)
All flashing
(All six indictors flash simultaneously.)
Elevator-like lighting
(Two adjacent indicators simultaneously
light so that lighting moves up and down.)
Accordion-like lighting
(Some or all indicators simultaneously light
so that lighting moves like an accordion.)
(frequency A)
Display mode
OFF (left)
(
See table below. *1
Slow
Lit
---
A
)
1
2
3
4
5
6
7
8
DIP switches
(frequency B)
2 and 3
ON (right)
Flashing
Not lit
Lit
(
Number of
Fast
addresses
---
−
−
−
−
−
−
−
−
B
1
2
4
8
16
32
64
128
)
7
Receivers
Weight
The weight of the F3W-D052U in the UNI-WIRE SYSTEM is the
weight of one terminal consisting of the Emitter and Receiver pair.
IDs
IDs are set separately for the Emitter and the Receiver.
Note: The ID is an identification number for broken wire position detection.
Power Supply
If a power voltage drop occurs in a remote section, consider using a
local (separate) power supply.
switch 1
1
2
3
4
5
6
Emitter:
Receiver: The control output address setting is the ID address.
DIP
(c)Copyright OMRON Corporation 2008 All Rights Reserved.
1 Flash Pattern
2
3
4 Operation mode setting
5
6
Frequency Setting
(F3W-D052U@ only) *4
(picking display mode setting)
Flash Time *2
(picking indicator flashing speed
setting)
Sensing distance (sensitivity)
setting
The picking instruction input address setting is the ID
address.
Function
(frequency A)
(1 to 3 m)
OFF (left)
Dark-ON
LONG
mode
(
Slow
See table below. *1
A
)
(frequency B)
(0.05 to 1 m)
ON (right)
Light-ON
SHORT
mode
(
Fast
B
)
7