D-110-0217 TE Connectivity, D-110-0217 Datasheet

D-110-0217

Manufacturer Part Number
D-110-0217
Description
Manufacturer
TE Connectivity
Type
Splice Terminalr
Datasheet
1.D-110-0217.pdf (4 pages)

Specifications of D-110-0217

Operating Temp Range
-55C to 150C
Product Length (mm)
9.4mm
Color
Transparent Blue
Product Type
Wire Splice
Splice Type
SolderSleeve
Connection Type
Solder
Inside Diameter (mm [in])
1.00 [0.040]
Length (mm [in])
9.10 [0.358]
Cma (min.-max) (cma [mm²])
200 – 608 [0.10 – 0.30]
Inside Diameter Fully Recovered (mm [in])
0.60 [0.025]
Rohs/elv Compliance
ELV compliant
Lead Free Solder Processes
Not relevant for lead free process
Rohs/elv Compliance History
Always was ELV compliant
Fluid Resistance
Splash Protection
Operating Temperature (max.) (°c)
150
Wire Temperature Rating Range (max.)
125° C to 150° C
Application
Wire to Wire Splicing
Lead Free Status / RoHS Status
Compliant
Product Facts
I
I
I
I
I
Available in:
Catalog 1654025
Revised 12-04
www.tycoelectronics.com
Transparent polyvinylidene
fluoride or polyolefin
insulation sleeve provides
encapsulation,
inspectability, strain relief,
and insulation
Prefluxed solder preform
offers a controlled soldering
process
One-piece design means
easy installation and low
installed cost
Optional tape carrier
provides convenience and
ease of installation
UL and CUL
Recognized
Americas
Europe
Asia Pacific
R
Dimensions are in millimeters
and inches unless otherwise
specified. Values in brackets
are U.S. equivalents.
I
I
I
Wire Termination to Pin/Post/Tab
Applications
Used for terminating wires
to component terminals,
such as motor tabs, con-
nector pins, and switch
terminals.
Product selection process
1. Determine the application
2. From the Product Options
3. Determine your compo-
4. Determine your wire
SolderSleeve Discrete Wire Terminators
operating temperature.
table on the next page,
select the product series
appropriate for the appli-
cation, based on the tem-
perature required.
nent connection point
type (pin, post, or tab)
and dimensions.
gauge.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
5. Optional: Select tape
6. Select part number from
carrier center-to-center
spacing (D-71X series
only). This should match
center spacing of com-
ponent terminals.
the appropriate table:
I
I
For CWT series
(applications with low-
temperature wires—
below 125°C [257°F]),
use Table A.
For D-129/141/71X
series (applications with
wires rated higher than
125°C [257°F]), use
Table B.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
Installation
For proper installation of
these devices, the correct
heating tool and reflector
attachment must be used.
Either of the following
Raychem heating tools are
recommended:
I
I
Refer to Raychem installa-
tion procedure RCPS 200-
12 (for D-129, D-141, D-71X)
or RPIP 824-00 (for CWT)
for detailed instructions and
recommended reflector
attachment.
You will find ordering infor-
mation for these tools see
section 10.
HL1802E
AA-400 Super Heater
South America: 55-11-3611-1514
Japan: 81-44-900-5102
Singapore: 65-4866-151
UK: 44-1793-528171
8-39
8

Related parts for D-110-0217

Image
Part Number
Description
Manufacturer
Datasheet
Request R
D-110-0090
Part Number:
D-110-0090
Description:
D-110-0090
Manufacturer:
TE Connectivity
D-110-41
Part Number:
D-110-41
Description:
D-110-41
Manufacturer:
TE Connectivity
D-110-0181
Part Number:
D-110-0181
Description:
D-110-0181
Manufacturer:
TE Connectivity
Datasheet:
D-110-0181.pdf (1 page)
D-110-0083
Part Number:
D-110-0083
Description:
Manufacturer:
TE Connectivity
Datasheet:
D-110-0083.pdf (1 page)
D-110-0214
Part Number:
D-110-0214
Description:
Manufacturer:
TE Connectivity
Datasheet:
D-110-0214.pdf (1 page)

D-110-0217 Summary of contents

Page 1

... Raychem heating tools are recommended: I HL1802E I AA-400 Super Heater Refer to Raychem installa- 8 tion procedure RCPS 200- 12 (for D-129, D-141, D-71X) or RPIP 824-00 (for CWT) for detailed instructions and recommended reflector attachment. You will find ordering infor- mation for these tools see section 10. 8-39 ...

Page 2

... Wire Termination to Pin/Post/Tab SolderSleeve Discrete Wire Terminators Product Options Note: Cadmium-free option (B-152 series) is available for operating temperature of 125˚C [257˚F]. Table A. CWT Series (125°C [257°F] rated) Connection-point Type and Size W pin W post W tab 8-40 Catalog 1654025 Dimensions are in millimeters ...

Page 3

... AWG) and No.* Smaller* D-110-0062 D-110-0217 D-141-13 D-141-22 D-141-30 Note: Micro SolderSleeve terminators are used for attaching leads smaller than 26 AWG (0.15 mm than 0.6 [.025] wide. *The D-110 series sleeves are primarily for single wire terminations and do not have a wire stop. The D-141 series will accept either one or two wires ...

Page 4

... Wire Termination to Pin/Post/Tab SolderSleeve Discrete Wire Terminators Product Characteristics Material Insulation [D-129, D-141, D-71X] Insulation [CWT] Solder and flux [D-129, D-141, D-71X] Solder and flux [CWT] Typical Performance Voltage drop Tensile strength Dielectric strength Temperature rating [CWT] Temperature rating [D-129, D-141, D-71X] ...

Related keywords