DS26503L Maxim Integrated Products, DS26503L Datasheet - Page 84

• Manufacturer Part Number: DS26503L
• Description: Timers & Support Products E1-T1-J1 BITS Elemen t T1-E1-J1 BITS Elem
• Manufacturer: Maxim Integrated Products
• Type: Clock Recoveryr

Specifications of DS26503L

• Supply Voltage (max): 3.46 V
• Supply Voltage (min): 3.13 V
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Supply Current: 85 mA
• Package / Case: LQFP-64

Register Name:
Register Description:
Register Address:
Bit #
Name
Default
HW
Mode
Bit 0: Custom Line Driver Select (CLDS). Setting this bit to a one will redefine the operation of the transmit line driver.
When this bit is set to a one and LIC1.5 = LIC1.6 = LIC1.7 = 0, then the device will generate a square wave at the TTIP and
TRING outputs instead of a normal waveform. When this bit is set to a one and LIC1.5 = LIC1.6 = LIC1.7 ≠ 0, then the device
will force TTIP and TRING outputs to become open-drain drivers instead of their normal push-pull operation. This bit should
be set to zero for normal operation of the device.
Bit 1: Short Circuit Limit Disable (in E1 mode) (SCLD). Controls the 50mA (RMS) current limiter.
Bits 2 and 7: Unused, must be set = 0 for proper operation.
Bit 3: Jitter Attenuator Clock Select 0 (JACKS0). This bit, along with JACKS1 (LIC2.7), MPS0 (LIC4.6), and MPS1
(LIC4.7), controls the source for JA CLOCK from the MCLK pin. Note: This bit must be configured even if the jitter
attenuator is disabled. The clock and data recovery engine also uses the JA CLOCK. Setting this bit enables the 2.048MHz to
1.544MHz conversion PLL for T1 applications. See the table in the LIC4 register description for more details on setting up the
JA CLOCK source.
Bit 4: Transmit Alarm Indication Signal (TAIS)
Bit 5: Insert BPV (IBPV). A zero-to-one transition on this bit will cause a single BPV to be inserted into the transmit data
stream. Once this bit has been toggled from a zero to a one, the device waits for the next occurrence of three consecutive ones
to insert the BPV. This bit must be cleared and set again for a subsequent error to be inserted.
Bit 6: Line Interface Reset (LIRST). Setting this bit from a zero to a one will initiate an internal reset that resets the clock
recovery state machine and recenters the jitter attenuator. Normally this bit is only toggled on power-up. Must be cleared and
set again for a subsequent reset.
Bit 7: Jitter Attenuator Clock Select 1 (JACKS1). This bit, along with JACKS0 (LIC2.3), MPS0 (LIC4.6), and MPS1
(LIC4.7), controls the source for JA CLOCK from the MCLK pin. Note: This bit must be configured even if the jitter
attenuator is disabled. The clock and data recovery engine also uses the JA CLOCK. Setting this bit enables the 12.8MHz to
2.048MHz conversion PLL. See the table in the LIC4 register description for more details on setting up the JA CLOCK source.
0 = enable 50mA current limiter
1 = disable 50mA current limiter
0 = 2.048MHz to 1.544MHz PLL bypassed
1 = 2.048MHz to 1.544MHz PLL enabled
0 = transmit an unframed all-ones code
1 = transmit data normally
0 = 12.8MHz to 2.048MHz PLL bypassed
1 = 12.8MHz to 2.048MHz PLL enabled
JACKS1
7
0
0
LIRST
LIC2
Line Interface Control 2
31h
6
0
0
IBPV
5
0
0
PIN 10
TAIS
TAIS
4
0
84 of 122
JACKS0
JACKS0
PIN 46
3
0
—
2
0
0
SCLD
1
0
0
CLDS
0
0
0