ADG711BR Analog Devices Inc, ADG711BR Datasheet - Page 5

• Manufacturer Part Number: ADG711BR
• Description: Analog Switch Quad SPST 16-Pin SOIC N
• Manufacturer: Analog Devices Inc
• Type: Analog Switchr

Specifications of ADG711BR

• Package: 16SOIC N
• Maximum On Resistance: 8@3V Ohm
• Maximum High Level Output Current: 30 mA
• Maximum Turn-off Time: 7(Typ)@3V ns
• Maximum Turn-on Time: 13(Typ)@3V ns
• Switch Architecture: SPST
• Power Supply Type: Single
• Rohs Status: RoHS non-compliant
• Function: Switch
• Circuit: 4 x SPST - NO
• On-state Resistance: 4 Ohm
• Voltage Supply Source: Single Supply
• Voltage - Supply, Single/dual (±): 1.8 V ~ 5.5 V
• Current - Supply: 0.001µA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (0.154", 3.90mm Width)
• Multiplexer Configuration: Quad SPST
• Number Of Inputs: 4
• Number Of Outputs: 4
• Number Of Channels: 4
• Analog Switch On Resistance: 5@3VOhm
• Analog Switch Turn On Time: 13ns
• Analog Switch Turn Off Time: 7ns
• Package Type: SOIC N
• Power Supply Requirement: Single
• Single Supply Voltage (min): 1.8V
• Single Supply Voltage (typ): 3/5V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Power Dissipation: 520mW
• Supply Current: 0.001mA
• Mounting: Surface Mount
• Pin Count: 16
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Lead Free Status / Rohs Status: Not Compliant

REV. A
V
GND
S
D
IN
R
∆R
R
I
I
I
V
C
C
C
t
S
D
D
ON
DD
ON
FLAT(ON)
D
S
D
D
, I
(OFF)
(OFF)
ON
, C
(OFF)
(V
(OFF)
S
ADG711 In
0
1
Logic
0
1
S
(ON)
S
)
(ON)
Table I. Truth Table (ADG711/ADG712)
Table II. Truth Table (ADG713)
Most positive power supply potential.
Ground (0 V) reference.
Source terminal. May be an input or output.
Drain terminal. May be an input or output.
Logic control input.
Ohmic resistance between D and S.
On resistance match between any two chan-
nels, i.e., R
Flatness is defined as the difference between
the maximum and minimum value of on
resistance as measured over the specified
analog signal range.
Source leakage current with the switch “OFF.”
Drain leakage current with the switch “OFF.”
Channel leakage current with the switch “ON.”
Analog voltage on terminals D, S.
“OFF” switch source capacitance.
“OFF” switch drain capacitance.
“ON” switch capacitance.
Delay between applying the digital control
input and the output switching on.
ADG712 In
1
0
Switch 1, 4
OFF
ON
ON
max–R
Switch Condition
ON
OFF
Switch 2, 3
ON
OFF
ON
min.
TERMINOLOGY
–5–
t
t
Crosstalk
Off Isolation
Charge
Bandwidth
On Response
On Loss
OFF
Injection
D
Delay between applying the digital control
input and the output switching off.
“OFF” time or “ON” time measured
between the 90% points of both switches,
when switching from one address state to
another. (ADG713 only).
A measure of unwanted signal that is coupled
through from one channel to another as a
result of parasitic capacitance.
A measure of unwanted signal coupling
through an “OFF” switch.
A measure of the glitch impulse transferred
from the digital input to the analog output
during switching.
The frequency at which the output is attenu-
ated by 3 dB.
The frequency response of the “ON” switch.
The voltage drop across the “ON” switch,
seen on the on response vs. frequency plot as
how many dBs the signal is away from
0 dB at very low frequencies.
PIN CONFIGURATION
ADG711/ADG712/ADG713
GND
IN1
IN4
NC
D1
S1
S4
D4
(TSSOP/SOIC)
NC = NO CONNECT
1
2
3
4
5
6
7
8
(Not to Scale)
TOP VIEW
ADG711
ADG712
ADG713
16
15
14
13
12
11
10
9
IN2
D2
S2
V
NC
S3
D3
IN3
DD