MT88E43BSR1 Zarlink, MT88E43BSR1 Datasheet - Page 26
![no-image](/images/manufacturer_photos/0/7/726/zarlink_sml.jpg)
MT88E43BSR1
Manufacturer Part Number
MT88E43BSR1
Description
Caller ID CMOS 3.58MHz 3.3V/5V 24-Pin SOIC T/R
Manufacturer
Zarlink
Datasheet
1.MT88E43BS1.pdf
(29 pages)
Specifications of MT88E43BSR1
Package
24SOIC
Telecommunication Standards Supported
GR-30|SIN227|SIN242|SR-TSV-002476|TR-NWT-000030
Fabrication Technology
CMOS
Maximum Data Rate
1212 Bd
Typical Operating Supply Voltage
3.3|5 V
Typical Supply Current
3 mA
Minimum Operating Temperature
-40 °C
Maximum Operating Temperature
85 °C
Operating Frequency
3.58 MHz
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MT88E43BSR1
Manufacturer:
zarlink
Quantity:
53
Notes
1) In a CPE where AC power is not available, the designer may choose to switch over to line power when the CPE goes off-hook and
2) Non-FSK signals such as CAS, speech and DTMF tones are in the same frequency band as FSK. They will be demodulated and give
3) FSKen may be set high as soon as the CPE has finished sending the acknowledgment signal ACK. TR-NWT-000575 specifies that
4) FSKen should be set low when CD has become inactive.
5) In an unsuccessful attempt where the end office does not send the FSK signal, the CPE should unmute the handset and enable the
6) SR-TSV-002476 states that it is desirable that the CPE have an on/off switch for the CAS detector. See SW1 in Figure 4.
7) The total recognition time is t
8) The total tone absent time is t
StD
use battery power while on-hook. The CPE should also be CID (on-hook) capable because TR-NWT-000575 specifies that CIDCW
will be offered only to lines which subscribe to CID.
false data. The FSKen pin should be set low to disable the FSK demodulator when FSK is not expected.
ACK = DTMF D for non-ADSI CPE, A for ADSI CPE.
keypad after this interval.
to section “Dual Tone Detection Guard Time” on page 6 for details). V
section “Dual Tone Detection Guard Time” on page 6 for details). V
TIP/RING
:
OSCout
(Note 6)
FSKen
PWDN
DCLK
DATA
St/GT
ESt
CD
DR
Figure 20 - Input and Output Timing for Bellcore Off-hook Data Transmission, e.g., CIDCW
Note 1
CPE goes off-hook
Note 2
t
t
DP
t
t
PU
GP
REC
REC
ABS
Note 7
= t
= t
CAS
GP
GA
A
+ t
+ t
Note 8
DP
DA
, where t
, where t
CPE mutes handset & disables keypad
B
t
DA
V
TGt
t
t
ABS
GA
Zarlink Semiconductor Inc.
GP
GA
CPE sends
MT88E43B
is the tone present guard time and t
is the tone absent guard time and t
ACK
C
26
Note 3
TGt
Note 5
t
CP
TGt
D
is the comparator threshold (refer to Figure 4).
is the comparator threshold (refer to Figure 4).
Mark
E
Packet
DA
Data
DP
Data
F
is the tone absent detect time (refer to
is the tone present detect time (refer
CPE unmutes handset
and enables keypad
Note 4
G
A = 75-85ms
B = 0-100ms
C = 55-65ms
D = 0-500ms
E = 58-75ms
F = feature specific
G ≤ 50ms
t
CA
Data Sheet