HMPP-3860-TR2 Avago Technologies US Inc., HMPP-3860-TR2 Datasheet - Page 8

• Manufacturer Part Number: HMPP-3860-TR2
• Description: DIODE PIN RF SGL 50V 1A MINIPAK
• Manufacturer: Avago Technologies US Inc.
• Type: Attenuator/Switchr

Specifications of HMPP-3860-TR2

• Package / Case: 4-MiniPak (1412)
• Diode Type: PIN - Single
• Voltage - Peak Reverse (max): 50V
• Current - Max: 1A
• Capacitance @ Vr, F: 0.2pF @ 50V, 1MHz
• Resistance @ If, F: 22 Ohm @ 1mA, 100MHz
• Configuration: Single
• Reverse Voltage: 10 V
• Forward Continuous Current: 1 A
• Frequency Range: UHF
• Termination Style: SMD/SMT
• Carrier Life: 0.5 us
• Maximum Diode Capacitance: 0.2 pF at 50 V
• Maximum Operating Temperature: + 150 C
• Maximum Series Resistance @ Maximum If: 1.5 Ohms at 100 mA
• Maximum Series Resistance @ Minimum If: 3 Ohms at 10 mA
• Minimum Operating Temperature: - 65 C
• Mounting Style: SMD/SMT
• Recovery Time: 80 ns
• Operating Temperature Classification: Military
• Package Type: SOT-23
• Mounting: Surface Mount
• Operating Temperature (max): 150C
• Operating Temperature (min): -65C
• Pin Count: 3
• Applications Frequency Range: UHF
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power Dissipation (max): -
• Lead Free Status / Rohs Status: Compliant

Assembly Information
The MiniPak diode is mounted to the PCB or microstrip
board using the pad pattern shown in Figure 17.
Figure 1. PCB Pad Layout, MiniPak (dimensions in mm).
This mounting pad pattern is satisfactory for most ap-
plications. However, there are applications where a high
degree of isolation is required between one diode and the
other is required. For such applications, the mounting pad
pattern of Figure 18 is recommended.
Figure 13. PCB Pad Layout, High Isolation MiniPak (dimensions in mm).
This pattern uses four via holes, connecting the crossed
ground strip pattern to the ground plane of the board.
8
0.40 mm via hole
(4 places)
0.8
0.40
0.4
0.5
2.60
0.4
0.20
0.3
0.5
0.3
2.40
SMT Assembly
Reliable assembly of surface mount components is a
complex process that involves many material, process, and
equipment factors, including: method of heating (e.g., IR
or vapor phase reflow, wave soldering, etc.) circuit board
material, conductor thickness and pattern, type of solder
alloy, and the thermal conductivity and thermal mass of
components. Components with a low mass, such as the
MiniPak package, will reach solder reflow temperatures
faster than those with a greater mass.
After ramping up from room temperature, the circuit board
with components attached to it (held in place with solder
paste) passes through one or more preheat zones. The
preheat zones increase the temperature of the board and
components to prevent thermal shock and begin evapo-
rating solvents from the solder paste. The reflow zone
briefly elevates the temperature sufficiently to produce a
reflow of the solder.
The rates of change of temperature for the ramp-up and
cool-down zones are chosen to be low enough to not
cause deformation of the board or damage to components
due to thermal shock. The maximum temperature in the
reflow zone (T
These parameters are typical for a surface mount assembly
process for Avago diodes. As a general guideline, the circuit
board and components should be exposed only to the
minimum temperatures and times necessary to achieve a
uniform reflow of solder.
MAX
) should not exceed 260°C.