CBT3384DK-T NXP Semiconductors, CBT3384DK-T Datasheet - Page 5

• Manufacturer Part Number: CBT3384DK-T
• Description: Bus Switch 2-Element 5-IN 24-Pin SSOP T/R
• Manufacturer: NXP Semiconductors

Specifications of CBT3384DK-T

• Package: 24SSOP
• Configuration: 5 x 1:1
• Logic Family: CBT
• Logic Function: Bus Switch
• Number Of Elements Per Chip: 2
• Number Of Outputs Per Chip: 10
• Typical Operating Supply Voltage: 5 V
• Maximum On Resistance: 10(Typ) Ohm
• Maximum High Level Output Current: -128 mA
• Maximum Low Level Output Current: 128 mA
• Maximum Operating Supply Voltage: 5.5 V
• Minimum Operating Supply Voltage: 4.5 V
• Maximum Propagation Delay Time @ Maximum Cl: 0.25@5V ns

NXP Semiconductors
Table 6.
Voltages are referenced to GND (ground = 0 V).
[1]
[2]
[3]
10. Dynamic characteristics
Table 7.
Voltages are referenced to GND (ground = 0 V). For test circuit see
[1]
[2]
CBT3384_6
Product data sheet
Symbol
R
Symbol Parameter
t
t
t
t
t
pd
PZH
PZL
PHZ
PLZ
ON
All typical values are at V
This is the increase in supply current for each input that is at the specified TTL voltage level rather than V
Measured by the voltage drop between the nAn and the nBn terminals at the indicated current through the switch. ON resistance is
determined by the lowest voltage of the two (nAn or nBn) terminals.
The propagation delay is the calculated RC time constant of the typical ON resistance of the switch and the specified load capacitance,
when driven by an ideal voltage source (zero output impedance).
t
pd
is the same as t
propagation delay
OFF-state to HIGH
propagation delay
OFF-state to LOW
propagation delay
HIGH to OFF-state
propagation delay
LOW to OFF-state
propagation delay
Parameter
ON resistance
Static characteristics
Dynamic characteristics
PLH
and t
CC
PHL
= 5 V, T
Conditions
nAn, nBn to nBn, nAn;
see
nOE to nAn or nBn;
see
nOE to nAn or nBn;
see
nOE to nAn or nBn;
see
nOE to nAn or nBn;
see
.
V
V
V
V
V
…continued
CC
CC
CC
CC
CC
Figure 5
Figure 6
Figure 6
Figure 6
Figure 6
amb
= 5.0 V
= 5.0 V
= 5.0 V
= 5.0 V
= 5.0 V
Conditions
V
V
V
= 25 C.
CC
CC
CC
= 4.5 V; V
= 4.5 V; V
= 4.5 V; V
0.5 V
0.5 V
0.5 V
0.5 V
0.5 V
Rev. 06 — 2 November 2009
I
I
I
= 0 V; I
= 0 V; I
= 2.4 V; I
[1][2]
I
I
= 64 mA
= 30 mA
I
= 15 mA
Min
1.2
1.2
1.7
1.7
Figure
-
T
amb
10-bit bus switch with 5-bit output enables
7.
Typ
2.3
2.3
3.6
2.7
= 25 C
-
[3]
[3]
[3]
Max
0.25
5.7
5.7
5.2
5.2
Min
T
-
-
-
amb
T
= 40 C to +85 C
amb
Min
Typ
1.2
1.2
1.7
1.7
CC
-
= 40 C to +85 C Unit
10
5
5
or GND.
[1]
CBT3384
© NXP B.V. 2009. All rights reserved.
Max
Max
0.25
15
5.6
6.0
5.5
6.6
7
7
Unit
5 of 14
ns
ns
ns
ns
ns